RTP Payload Format for Haptics

Introduction Haptics provides users with tactile effects in addition to audio and video, allowing them to experience sensory immersion. Haptic data is mainly transmitted to devices that act as actuators and provides them with information to operate according to the values defined in haptic effects. The IETF registered haptics as a primary media type akin to audio and video . The MPEG Haptics Coding standard defines the data formats, metadata, and codec architecture to encode, decode, synthesize and transmit haptic signals. It defines the "MIHS unit" as a unit of packetization suitable for streaming, and similar in essence to the NAL unit defined in some video specifications. This document describes how haptic data (MIHS units) can be transmitted using the RTP protocol. This document followed recommendations in and for RTP payload format writers.

Conventions The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 when, and only when, they appear in all capitals, as shown here.

Definition This document uses the definitions of the MPEG Haptics Coding standard . Some of these terms are provided here for convenience. Actuator: component of a device for rendering haptic sensations. Avatar: body (or part of body) representation. Band: component in a channel for containing effects for a specific range of frequencies. Channel: component in a perception containing one or more bands rendered on a device at a specific body location. Device: physical system having one or more actuators configured to render a haptic sensation corresponding with a given signal. Effect: component of a band for defining a signal, consisting of a haptic waveform or one or more haptic keyframes. Experience: top level haptic component containing perceptions and metadata. Haptics: tactile sensations. Keyframe: component of an effect mapping a position in time or space to an effect parameter such as amplitude or frequency. Metadata: global information about an experience, perception, channel, or band. MIHS unit: unit of packetization of the MPEG-I Haptic Stream format, which is used as unit of payload in the format described in this memo. See for details. Modality: type of haptics, such as vibration, force, pressure, position, velocity, or temperature. Perception: haptic perception containing channels of a specific modality. Signal: representation of the haptics associated with a specific modality to be rendered on a device. Hmpg format: hmpg is a binary compressed format for haptics data. Information is stored in a binary form and data compression is applied on data at the band level. The haptics/hmpg media subtype is registered in and updated by this memo. Independent unit: a MIHS unit is independent if it can be decoded independently from earlier units. Independent units contain timing information and are also called "sync units" in . Dependent unit: a MIHS unit is dependent if it requires earlier units for decoding. Dependent units do not contain timing information and are also called "non-sync units" in . Time-independent effect: a haptic effect that occurs regardless of time. The tactile feedback of a texture is a representative example. Time-independent effects are encoded in spatial MIHS units, defined in . Time-dependent effect: a haptic effect that varies over time. For example, tactile feedback for vibration and force are time-dependent effects, and are encoded in temporal MIHS units, defined in .

Haptic Format Description

Overview of Haptic Coding The MPEG Haptics Coding standard specifies methods for efficient transmission and rendering of haptic signals, to enable immersive experiences. It supports multiple types of perceptions, including the most common vibrotactile (sense of touch that perceives vibrations) and kinesthetic perceptions (tactile resistance or force), but also other, less common perceptions, including for example the sense of temperature or texture. It also supports two approaches for encoding haptic signals: a "quantized" approach based on samples of measured data, and a "descriptive" approach where the signal is synthesized using a combination of functions. Both quantized and descriptive data can be encoded in a human-readable exchange format based on JSON (.hjif), or in a binary packetized format for distribution and streaming (.hmpg). This last format is referred to as the MPEG-I Haptic Stream (MIHS) format and is a base for the RTP payload format described in this document.

MPEG-I Haptic Stream (MIHS) format MIHS is a stream format used to transport haptic data. Haptic data including haptic effects is packetized according to the MIHS format, and delivered to actuators, which operate according to the provided effects. The MIHS format has two levels of packetization, MIHS units and MIHS packets. MIHS units are composed of a MIHS unit header and zero or more MIHS packets. Four types of MIHS units are defined. An initialization MIHS unit contains MIHS packets carrying metadata necessary to reset and initialize a haptic decoder, including a timestamp. A temporal MIHS unit contains one or more MIHS packets defining time-dependent effects and providing modalities such as pressure, velocity, and acceleration. The duration of a temporal unit is a positive number. A spatial MIHS unit contains one or more MIHS packets providing time-independent effects, such as vibrotactile texture, stiffness, and friction. The duration of a spatial unit is always zero. A silent MIHS unit indicates that there is no effect during a time interval and its duration is a positive number. A MIHS unit can be marked as independent or dependent. When a decoder processes an independent unit, it resets the previous effects and therefore provides a haptic experience independent from any previous MIHS unit. A dependent unit is the continuation of previous MIHS units and cannot be independently decoded and rendered without having decoded previous MIHS unit(s). Initialization and spatial MIHS units are always independent units. Temporal and silent MIHS units can be dependent or independent units. illustrates a succession of MIHS units in a MIHS stream.

Example of MIHS stream

Payload Format For Haptics

RTP Header Usage The RTP header is defined in and represented in . Some of the header field values are interpreted as follows.

RTP header for Haptic. Payload type (PT): 7 bits. The assignment of a payload type MUST be performed either through the profile used or in a dynamic way. TimeStamp (TS): 32 bits. A timeStamp representing the sampling time of the first sample of the MIHS unit in the RTP payload. The clock frequency MUST be set to the sample rate of the encoded haptic data and is conveyed out-of-band (e.g., as an SDP parameter). Marker bit (M): 1 bit. The marker bit SHOULD be set to one in the first non-silent RTP packet after a period of haptic silence. This enables jitter buffer adaptation and haptics device washout (i.e., reset to a neutral position) prior to the beginning of the burst with minimal impact on the quality of experience for the end user. The marker bit in all other packets MUST be set to zero.

Payload Header The RTP payload header follows the RTP header. describes the RTP payload header for Haptic.

RTP Payload Header for Haptic. D (Dependency, 1 bit): this field is used to indicate whether the MIHS unit included in the RTP payload is, when its value is one, dependent or, when its value is zero, independent. UT (Unit Type, 3 bits): this field indicates the type of the MIHS unit included in the RTP payload. UT field values are listed in . L (MIHS Layer, 4 bits): this field is an integer value which indicates the priority order of the MIHS unit included in the RTP payload, as determined by the haptic sender (e.g., by the haptic codec), based on application-specific needs. For example, the sender may use the MIHS layer to prioritize perceptions with the largest impact on the end-user experience. Zero corresponds to the highest priority. The semantic of individual MIHS layers are not specified and left for the application to assign.

Payload Structures Three different types of RTP packet payload structures are specified. A single unit packet contains a single MIHS unit in the payload. A fragmentation unit contains a subset of a MIHS unit. An aggregation packet contains multiple MIHS units in the payload. The unit type (UT) field of the RTP payload header, as shown in , identifies both the payload structure and, in the case of a single-unit structure, also identifies the type of MIHS unit present in the payload.

Payload structure type for haptic The payload structures are represented in . The single unit payload structure is specified in . The fragmented unit payload structure is specified in . The aggregation packet payload structure is specified in .

RTP Transmission modes

Single Unit Payload Structure In a single unit payload structure, as described in , the RTP packet contains the RTP header, followed by the payload header and one single MIHS unit. The payload header follows the structure described in . The payload contains a MIHS unit as defined in .

Single Unit Payload Structure

Fragmented Unit Payload Structure In a fragmented unit payload structure, as described in , the RTP packet contains the RTP header, followed by the payload header, a Fragmented Unit (FU) header, and a MIHS unit fragment. The payload header follows the structure described in . The value of the UT field of the payload header is 7. The FU header follows the structure described in .

Fragmentation Unit Payload Structure FU headers are used to enable fragmenting a single MIHS unit into multiple RTP packets. Fragments of the same MIHS unit MUST be sent in consecutive order with ascending RTP sequence numbers (with no other RTP packets within the same RTP stream being sent between the first and last fragment). FUs MUST NOT be nested, i.e., an FU MUST NOT contain a subset of another FU. describes a FU header, including the following fields:

Fragmentation unit header FUS (Fragmented Unit Start, 1 bit): this field MUST be set to 1 for the first fragment, and 0 for the other fragments. FUE (Fragmented Unit End, 1 bit): this field MUST be set to 1 for the last fragment, and 0 for the other fragments. RSV (Reserved, 3 bits): these bits MUST be set to 0 by the sender and ignored by the receiver. UT (Unit Type, 3 bits): this field indicates the type of the MIHS unit this fragment belongs to, using values defined in . The use of MIHS unit fragmentation in RTP means that a media receiver can receive some fragments, but not other fragments. The missing fragments will typically not be retransmitted by RTP. This results in partially received MIHS units, which can be either dropped or used by the decoding application, based on implementation.

Aggregation Packet Payload Structure In an aggregation packet, as described in , the RTP packet contains an RTP header, followed by a payload header, and, for each aggregated MIHS Unit, a MIHS unit size followed by the MIHS unit. The payload header follows the structure described in .

Single-Time Aggregation Packet shows a Single-Time Aggregation Packet (STAP), which can be used to transmit multiple MIHS units that correspond to the same timestamp. For example, if two frequencies are used for the same content, they can be transmitted at once in a STAP. Multiple spatial units can also be sent together in a STAP, since this type of haptics data is time independent. The MIHS unit length field (16 bits) holds the length of the MIHS unit following it, in bytes. The value of the UT field of the payload header is 5.

Multiple-time aggregation packet shows a multi-time aggregation packet. It is used to transmit multiple MIHS units with different timestamps, in one RTP packet. Multi-time aggregation can help reduce the number of packets, in environments where some delay is acceptable. The value of the UT field of the Payload Header is 6. The MIHS unit length field (16 bits) holds the length of the MIHS unit following it, in bytes. The timestamp offset field (TS offset, 16 bits) is present in the MTAP case, and MUST be set to the value of (time of the MIHS unit - RTP timestamp of the packet). The timestamp offset of the earliest aggregation unit MUST always be zero. Therefore, the RTP timestamp of the MTAP is identical to the earliest MIHS unit time.

MIHS Units Transmission Considerations The following considerations apply for the streaming of MIHS units over RTP: The MIHS format enables variable duration units and uses initialization MIHS units to declare the duration of subsequent non-zero duration MIHS units, as well as the maximum variation of this duration. A sender SHOULD set constant or low-variability (e.g., lower than the playout buffer) durations in initialization MIHS units, for RTP streaming. This enables the receiver to determine early (e.g., using a timer) when a unit has been lost and make the decoder more robust to RTP packet loss. If a sender sends MIHS units with high duration variations, the receiver MAY need to wait for a long period of time (e.g., the upper bound of the duration variation), to determine if a MIHS unit was lost in transmission. Whether this behavior is acceptable or not is application dependent. The MIHS format uses silent MIHS units to signal haptic silence. A sender MAY decide not to send silent units, to save network resources. Since, from a receiver standpoint, a missed MIHS unit MAY originate from a not-sent silent unit, or a lost packet, a sender MAY send one, or a few, MIHS silent units at the beginning of a haptic silence. If a media receiver receives a MIHS silent unit, the receiver SHOULD assume that silence is intended until the reception of a non-silent MIHS unit. This can reduce the number of false detections of lost RTP packets by the decoder. In some multimedia conference scenarios using an RTP video mixer (e.g., when adding or selecting a new source), it is recommended to use Full Intra Request (FIR) feedback messages with Haptics . The purpose of the FIR message is to cause an encoder to send a decoder refresh point at the earliest opportunity. In the context of haptics, an appropriate decoder refresh point is an initialization MIHS unit. The initialization MIHS unit point enables a decoder to be reset to a known state and be able decode all MIHS units following it.

Payload Format Parameters This section describes payload format parameters. updates the 'haptics' Media Type Registration and specifies new optional parameters. further registers a new token in the media sub-registry of the Session Description Protocols (SDP) Parameters registry.

Media Type Registration Update This memo updates the 'hmpg' haptic subtype defined in for use with the MPEG-I haptics streamable binary coding format described in ISO/IEC 23090-31: Haptics coding . This memo especially defines optional parameters for this type in . The original subtype registration for haptics/hmpg, registered with IANA in , did not include any required or optional parameters. This document introduces optional parameters to enable extended functionality while maintaining backward compatibility. A mapping of the parameters into the Session Description Protocol (SDP) is also provided for applications that use SDP. Equivalent parameters could be defined elsewhere for use with control protocols that do not use SDP. The receiver MUST ignore any parameter unspecified in this memo. The following entries identify the media type being updated: Type name: haptics Subtype name: hmpg The following entries are replaced by this memo: Optional parameters: see section 6.2 of RFC XXX (note to RFC editor: replace with this RFC's number). Person & email address to contact for further information: Yeshwant Muthusamy (yeshwant@yeshvik.com) and Hyunsik Yang (hyunsik.yang@interdigital.com)

Optional Parameters Definition ver provides the year of the edition and amendment of ISO/IEC 23090-31 that this file conforms to, as defined in . MPEG_haptics object.version is a string which may hold values such as XXXX or XXXX-Y where XXXX is the year of publication and Y is the amendment number, if any. For the initial release of the specifications, the value is "2023". profile indicates the profile used to generate the encoded stream as defined in : MPEG_haptics object.profile is a string which may in the initial release of the specifications hold the values "simple-parametric" or "main". lvl indicates the level used to generate the encoded stream as defined in : MPEG_haptics object.level is an integer which may in the initial release of the specifications hold the values 1 or 2. maxlod indicates the maximum level of details to use for the avatar(s). The avatar level of detail (LOD) is defined in : MPEG_haptics.avatar object.lod is an integer which MAY in the initial release of the specifications hold 0 or a positive integer. avtypes indicates, using a comma-separated list, types of haptic perception represented by the avatar(s). The avatar type is defined in : MPEG_haptics.avatar object.type is a string which MAY in the initial release of the specifications hold values among "Vibration", "Pressure", "Temperature", "Custom". modalities indicates, using a comma-separated list, haptic perception modalities (e.g., pressure, acceleration, velocity, position, temperature, etc.). The perception modality is defined in : MPEG_haptics.perception object.perception_modality is a string which MAY in the initial release of the specifications hold values among "Pressure", "Acceleration", "Velocity", "Position", "Temperature", "Vibrotactile", "Water", "Wind", "Force", "Electrotactile", "Vibrotactile Texture", "Stiffness", "Friction", "Humidity", "User-defined Temporal", "User-defined Spatial", "Other". bodypartmask indicates, using a bitmask, the location of the devices or actuators on the body. The body part mask is defined in : MPEG_haptics.reference_device object.body_part_mask is a 32-bit integer which MAY in the initial release of the specifications hold a bit mask using bit positions defined in table 7 of . maxfreq indicates the maximum frequency of haptic data for vibrotactile perceptions (Hz). Maximum frequency is defined in : MPEG_haptics.reference_device object.maximum_frequency is defined as an integer or floating-point number in the initial release of the specifications. minfreq indicates the minimum frequency of haptic data for vibrotactile perceptions (Hz). Minimum frequency is defined in : MPEG_haptics.reference_device object.minimum_frequency is defined as an integer or floating-point number in the initial release of the specifications. dvctypes indicates, using a comma-separated list, the types of actuators. The device type is defined in : MPEG_haptics.reference_device object.type is a string which MAY in the initial release of the specifications hold values among "LRA", "VCA", "ERM", "Piezo" or "Unknown". silencesupp indicates whether silence suppression SHOULD be used (1) or not (0). The default value SHALL be 0.

SDP Parameter Registration This memo registers a 'haptics' token in the media sub-registry of the Session Description Protocols (SDP) Parameters registry. This registration contains the required information elements outlined in the SDP registration procedure defined in section 8.2 of . (1) Contact Information: (2) Name being registered (as it will appear in SDP): haptics (3) Long-form name in English: haptics (4) Type of name ('media', 'proto', 'fmt', 'bwtype', 'nettype', or 'addrtype'): media (5) Purpose of the registered name: (6) Specification for the registered name: RFC XXXX RFC Editor Note: Replace RFC XXXX with the published RFC number.

SDP Considerations The mapping of above defined payload format media type to the corresponding fields in the Session Description Protocol (SDP) is done according to . The media name in the "m=" line of SDP MUST be haptics. The encoding name in the "a=rtpmap" line of SDP MUST be hmpg The clock rate in the "a=rtpmap" line MAY be any sampling rate, typically 8000. The OPTIONAL parameters (defined in ), when present, MUST be included in the "a=fmtp" line of SDP. This is expressed as a media type string, in the form of a semicolon-separated list of parameter=value pairs. An example of media representation corresponding to the hmpg RTP payload in SDP is as follows:

SDP Offer/Answer Considerations When using the offer/answer procedure described in to negotiate the use of haptic, the following considerations apply: When used for a unidirectional stream, the SDP parameters represent the properties of the sender (on the sending side) and of the receiver (on the receiving side). When used for a sendrecv stream, the SDP parameters represent the properties of the receiver. The receiver properties expressed using the SDP parameters 'ver', 'profile' and 'lvl' have a mandatory character, since they represent implementation capabilities. The ver, profile, lvl parameters MUST be used symmetrically in SDP offer and answer. That is, their values in the answer MUST match those in the offer, either explicitly signaled or implicitly inferred. In the same session, ver, profile, and lvl MUST NOT be changed in subsequent offers or answers. The properties expressed using SDP parameters other than 'ver', 'profile' and 'lvl' are provided as recommendations for efficient data transmission and are not binding, meaning that a sender is encouraged but not required to conform to the parameters specified by the receiver. These properties MAY be set to different values in offers and answers. These properties MAY be updated in subsequent offers or answers. Any receiver compliant with MUST accept any stream with a compatible version, profile and level. A receiver supporting a more general profile will accept a stream corresponding to a same or less general profile (e.g., "main" is more general than "simple-parametric"). A receiver supporting a given level will accept a stream corresponding to a same or lower level. A receiver supporting a given version will accept a stream corresponding to the same version and MAY accept other versions. A receiver MAY ignore any part of a received stream, e.g., that it does not have support for rendering. The haptic signal can be sampled at different rates. The MPEG Haptics Coding standard does not mandate a specific frequency. A typical sample rate is 8000Hz. The parameter 'ver' indicates the version of the haptic standard specification. If it is not specified, the initial version of the MPEG Haptic Coding specification SHOULD be assumed, although the sender and receiver MAY use a specific value based on an out-of-band agreement. The parameter 'profile' is used to restrict the number of tools used (e.g., the simple-parametric profile fits enable simpler implementations than the main profile). If it is not specified, the most general profile "main" SHOULD be assumed, although the sender and receiver MAY use a specific value based on an out-of-band agreement. The parameter 'lvl' is used to further characterize implementations within a given profile, e.g., according to the maximum supported number of channels, bands, and perceptions. If it is not specified, the most general level "2" SHOULD be assumed, although the sender and receiver MAY use a specific version based on an out-of-band agreement. Other parameters can be used to indicate bitstream properties as well as receiver capabilities. The parameters 'maxlod', 'avtypes', 'bodypartmask', 'maxfreq', 'minfreq', 'dvctypes', and 'modalities' can be sent by a sender to reflect the characteristics of bitstreams and can be set by a receiver to reflect the nature and capabilities of local actuator devices, or a preferred set of bitstream properties. For example, different receivers MAY have different sets of local actuators, in which case these parameters can be used to select a stream adapted to the receiver. In some other cases, some receivers MAY indicate a preference for a set of bitstream properties such as perceptions, min/max frequency, or body-part-mask, which contribute the most to the user experience for a given application, in which case these parameters can be used to select a stream which include and possibly prioritizes those properties. For example, if the haptic stream server provides more information than the body mask specified by the receiver, the additional information can be either integrated into a single effect or ignored by the receiver. The parameter 'silencesupp' can be used to indicate sender and receiver capabilities or preferences. This parameter indicates whether silence suppression SHOULD be used, as described in .

Declarative SDP Considerations When haptic content over RTP is offered with SDP in a declarative style, the parameters capable of indicating both bitstream properties as well as receiver capabilities are used to indicate only bitstream properties. For example, in this case, the parameters maxlod, bodypartmask, maxfreq, minfreq, dvctypes, and modalities declare the values used by the bitstream, not the capabilities for receiving bitstreams. A receiver of the SDP is required to support all parameters and values of the parameters provided; otherwise, the receiver MUST reject or not participate in the session. It falls on the creator of the session to use values that are expected to be supported by the receiving application.

Congestion Control Considerations The general congestion control considerations for transporting RTP data apply to HMPG haptics over RTP as well . It is possible to adapt network bandwidth usage by adjusting either the encoder bit rate or by adjusting the stream content (e.g., level of detail, body parts, actuator frequency range, target device types, modalities). In case of congestion, a receiver or intermediate node MAY prioritize independent packets over dependent ones, since the non-reception of an independent MIHS unit can prevent the decoding of multiple subsequent dependent MIHS units. In case of congestion, a receiver or intermediate node MAY prioritize initialization MIHS units over other units, since initialization MIHS units contain metadata used to re-initialize the decoder, and MAY drop silent MIHS units before other types of MIHS units, since a receiver MAY interpret a missing MIHS unit as a silence. It is also possible, using the layer field of the RTP payload header, to allocate MIHS units to different layers based on their content, to prioritize haptic data contributing the most to the user experience. In case of congestion, intermediate nodes and receivers SHOULD use the MIHS layer value to determine the relative importance of haptic RTP packets.

Security Considerations This RTP payload format is subject to security threats commonly associated with RTP payload formats, as well as threats specific to the interaction of haptic devices with the physical world, and threats associated with the use of compression by the codec. Security consideration for threats commonly associated with RTP payload formats are outlined in , as well as in RTP profiles such as RTP/AVP ), RTP/AVPF , RTP/SAVP , or RTP/SAVPF . Haptic sensors and actuators operate within the physical environment. This introduces the potential for information leakage through sensors, or damage to actuators due to data tampering. Additionally, misusing the functionalities of actuators (such as force, position, temperature, vibration, electro-tactile, etc.) MAY pose a risk of harm to the user, for example by setting keyframe parameters (e.g., amplitude, position, frequency) or channel gain to a value that surpasses a permissible range. While individual devices can implement security measures to reduce or eliminate those risks on a per-device basis, in some cases harm can be inflicted by setting values which are permissible for the individual device. For example, causing contact with the physical environment or triggering unexpected force feedback can potentially harm the user. Each haptic system should therefore implement system-dependent security measures, which are more error prone. To limit the risk that attackers exploit weaknesses in haptic systems, it is important that haptic transmission should be protected against malicious traffic injection or tampering. However, as "Securing the RTP Framework: Why RTP Does Not Mandate a Single Media Security Solution" discusses, it is not an RTP payload format's responsibility to discuss or mandate what solutions are used to meet the basic security goals like confidentiality, integrity, and source authenticity for RTP in general. This responsibility lays on anyone using RTP in an application. They can find guidance on available security mechanisms and important considerations in "Options for Securing RTP Sessions" . Applications SHOULD use one or more appropriate strong security mechanisms. The haptic codec used with this payload format uses a compression algorithm (see sections 8.2.8.5 and 8.3.3.2 in ). An attacker MAY inject pathological datagrams into the stream which are complex to decode and cause the receiver to be overloaded, similarly to . End-to-end security with authentication, integrity, or confidentiality protection will prevent a Media-Aware Network Element (MANE) from performing media-aware operations other than discarding complete packets. In the case of confidentiality protection, it will even be prevented from discarding packets in a media-aware way. To be allowed to perform such operations, a MANE is required to be a trusted entity that is included in the security context establishment.

IANA Considerations This memo updates a media type registration with IANA; see .

Acknowledgments Thanks to Philippe Guillotel, Quentin Galvane, Jonathan Lennox, Marius Kleidl and Stephan Wenger for the comments and discussions about this draft.