]> Nokia

sergio.belotti@nokia.com

Huawei

italo.busi@huawei.com

Nokia

dieter.beller@nokia.com

Orange

esther.lerouzic@orange.com

Futurewei Technologies

aihuaguo.ietf@gmail.com

CCAMP Working Group This document defines a collection of common data types, identities, and groupings in the YANG data modeling language. These common types and groupings, derived from the built-in YANG data types, identities, and groupings are intended to be imported by modules that model Layer 0 configuration and state capabilities, such as Wavelength Switched Optical Networks (WSONs) and flexi-grid Dense Wavelength Division Multiplexing (DWDM) networks. This document obsoletes RFC 9093 by replacing the YANG module it contained with a new revision that includes additional YANG data types, identities and groupings.

Introduction YANG is a data modeling language used to model configuration data, state data, Remote Procedure Calls, and notifications for network management protocols such as the Network Configuration Protocol (NETCONF) . The YANG language supports a small set of built-in data types and provides mechanisms to derive other types from the built-in types. This document introduces a collection of common data types derived from the built-in YANG data types. The derived types and groupings are designed to be the common types applicable for modeling Traffic Engineering (TE) features as well as non-TE features (e.g., physical network configuration aspects) for Layer 0 optical networks in model(s) defined outside of this document. The applicability of Layer 0 types specified in this document includes Wavelength Switched Optical Networks (WSONs) and , and flexi-grid Dense Wavelength Division Multiplexing (DWDM) networks . This document adds new type definitions to the YANG modules and obsoletes . For further details, see the revision statements of the YANG module in or the summary in . This document obsoletes by replacing it in its entirety. It provides a new revision of the YANG module contained in that RFC, and retains the data types previously defined, but also adds new type definitions to the YANG module. For further details, see . The YANG data model in this document conforms to the Network Management Datastore Architecture defined in .

Terminology and Notations Refer to and for the key terms used in this document, and the terminology for describing YANG data models can be found in . The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 when, and only when, they appear in all capitals, as shown here.

Prefix in Data Node Names In this document, names of data nodes and other data model objects are prefixed using the standard prefix associated with the corresponding YANG imported module. Prefix YANG module Reference te-types ietf-te-types [RFCYYYY] l0-types ietf-layer0-types RFC XXXX

• RFC Editor Note: Please replace XXXX with the RFC number assigned to this document. Please replace YYYY with the RFC number assigned to . Please remove this note.

Layer 0 Types Module Contents This document defines a YANG module for common Layer 0 types, ietf- layer0-types. This module is used for WSON and flexi-grid DWDM networks. The "ietf-layer0-types" module contains the following YANG reusable YANG data types, identities and groupings:

l0-grid-type:

A base YANG identity for the grid type as defined in and .

cwdm-ch-spc-type:

A base YANG identity for the Coarse Wavelength Division Multiplexing (CWDM) channel-spacing type as defined in .

dwdm-ch-spc-type:

A base YANG identity for the DWDM channel-spacing type as defined in .

flexi-ncfg-type:

A base YANG identity for the DWDM flexi-grid Nominal Central Frequency Granularity (NCFG) type as defined in .

• Note that the only value for NCFG standardized in is 6.25GHz.

flexi-slot-width-granularity:

A base YANG identity for the DWDM flexi-grid Slot Width Granularity (SWG) type, as defined in .

Note that the only value for SWG standardized in is 12.5GHz.

fec-type:

A base YANG identity from which specific FEC (Forward Error Correction) type identities are derived.

line-coding:

A base YANG identity from which specific identities defining the bit rate/line coding of optical tributary signals are derived.

wavelength-assignment:

A base YANG identity from which for Wavelength selection method, as defined in .

operational-mode:

A YANG data type used to identify an organization (e.g., vendor) specific mode for transceiver capability description, as defined in Section 2.5.2 of

wson-label-start-end:

The WSON label range was defined in , and the generic topology model defines the label-start/label-end in . This grouping shows the WSON-specific label-start and label-end information. See for more details.

wson-label-hop:

The WSON label range was defined in , and the generic topology model defines the label-hop in . This grouping shows the WSON-specific label-hop information. See for more details.

l0-label-range-info:

A YANG grouping that defines the Layer 0 label range information applicable for WSON as defined in . The label range info is defined per priority .

This grouping is used in the flexi-grid DWDM by adding more flexi-grid-specific parameters. See for more details.

wson-label-step:

A YANG grouping that defines label steps for WSON as defined in . See for more details.

flexi-grid-label-start-end:

The flexi-grid label range was defined in , and the generic topology model defines the label-start/label-end in .

This grouping shows the flexi-grid-specific label- start and label-end information which is used to describe the range of available nominal central frequencies. See for more details.

As described in section 3.1 of , the range of available nominal central frequencies are advertised for m=1, which means that for an available central frequency n, the frequency slot from central frequency n-1 to central frequency n+1 is available.

flexi-grid-label-hop:

The flexi-grid label range was defined in , and the generic topology model defines the label-hop in .

This grouping shows the WSON-specific label-hop information. See for more details.

flexi-grid-label-range-info:

A YANG grouping that defines flexi-grid label range information as defined in . See for more details. See for more details.

flexi-grid-label-step:

A YANG grouping that defines flexi-grid label steps as defined in . See for more details.

wdm-label-start-end:

A YANG grouping that combines the definition of label-start/label-end information that was defined separately in wson-label-start-end and flexi-grid-label-start-end, to support optical network scenarios that contain both fixed- and flexi-grid links. See for more details.

wdm-label-hop:

A YANG grouping that combines the definition of label hop information that was defined separately in wson-label-hop and flexi-grid-label-hop, to support optical network scenarios that contain both fixed- and flexi-grid links. See for more details.

wdm-label-range-info:

A YANG grouping that combines the definition of label range information that was defined separately in wson-label-range-info and flexi-grid-label-range-info, to support optical network scenarios that contain both fixed- and flexi-grid links. See for more details.

wdm-label-step:

A YANG grouping that combines the definition of label step information defined separately in wson-label-step and flexi-grid-label-step, to support optical network scenarios that contain both fixed- and flexi-grid links. See for more details.

transceiver-capabilities:

A YANG grouping to define the transceiver capabilities (also called "modes") needed to determine optical signal compatibility.

standard-mode:

A YANG grouping for the standard modes defined in .

organizational-mode:

A YANG grouping to define transponder operational mode supported by organizations or vendors, as defined in .

explicit-mode:

A YANG grouping to define the list of attributes related to optical impairments limits in case of transceiver explicit mode, as defined in .

Note that the the actual portion of the spectrum occupied by an OTSi is not explicitly reported within the explicit-mode parameters because it can be calculated using the available-baud-rate, the roll-off and the min-carrier-spacing attributes.

transmitter-tuning-range:

A YANG grouping that defines the transmitter tuning range, which includes the minimum and maximum tuning frequency, as well as the frequency tuning steps.

common-organizational-explicit-mode:

A YANG grouping to define the common capabilities attributes limit range in case of operational mode and explicit mode.

modulation:

A base YANG identity to define the different modulation types, as defined in

snr:

A YANG data type used to represent an (Optical) Signal to Noise Ratio measured over 0.1 nm resolution bandwidth, as defined in

psd:

A YANG data type used to represent a Power Spectral Density (PSD), as defined in

penalty-value:

A YANG grouping to define the penalty value for multiple penalty types, such as Chromatic Dispersion (CD), Polarization Mode Dispersion (PMD), as defined in or Polarization Dependent Loss(PDL)

switching-wson-lsc:

A YANG identity for the Wavelength Switched Optical Network Lambda-Switch Capable (WSON-LSC) interface switching capability as defined in .

switching-flexi-grid-lsc:

A YANG identity for the Flexi-Grid Lambda-Switch Capable (Flexi-Grid-LSC) interface switching capability as defined in .

It is worth noting that there is an inheritance relationship between the Lambda-Switch Capable (LSC) switching capability, defined in , and the WSON-LSC and Flexi-Grid-LSC, defined respectively in and . As a consequence, the 'switching-wson-lsc' and 'switching-flexi-grid-lsc' YANG identities are defined as derived identities from the 'switching-lsc', defined in .

WDM Label and Label Range As described in and , the WDM label represents the frequency slot assigned to a WDM Label Switched Path (LSP) on a given WDM Link, which models an Optical Multiplex Section (OMS) Media Channel Group (MCG) as described in . The same WDM label shall be assigned to the same WDM LSP on all the WDM Links on a regen-free LSP path or path segment. A frequency slot is defined in as a contiguous frequency range characterized by its nominal central frequency and slot width. The frequency range allocated to a frequency slot is unavailable to other frequency slots. The definition of the frequency slot depends on the WDM grid type: In case of CWDM fixed-grid, defined in , the frequency slot is defined by a fixed CWDM channel spacing (cwdm-ch-spc-type) and by the nominal central wavelength which is computed as described in . The formula in is copied here for reader convenience:

• where 'n' is defined in as integer (positive, negative, or 0)

In case of DWDM fixed-grid, defined in , the frequency slot is defined by a fixed DWDM channel spacing (dwdm-ch-spc-type) and by the nominal central frequency, which is computed as described in . The formula in is copied here for reader convenience:

• where 'n' is defined in as integer (positive, negative, or 0)

In case of DWDM flexible-grid, defined in , the frequency slot is defined by the slot width and by the nominal central frequency, which are computed, based on the slot width granularity (SWG, fixed at 12.5GHz in ), and of the nominal central frequency granularity (NCFG, fixed at 6.25GHz in ) respectively, as described in and . The formulas in can be generalized as follows:

• where 'n' is defined in as integer (positive, negative, or 0) and 'm' is defined in as an integer greater than or equal to 1.

The definition of the channel spacing, NCFG and SWG in the YANG model have been generalized to support modelling of vendor-specific values (e.g., finer vendor-specific granularity for NCFG and SWG). The WDM Label Range represents the frequency slots that are available for WDM LSPs to be set up over a given WDM Link. The WDM Label Range is defined by augmenting the label-restriction list, defined in , with WDM technology-specific attributes, using the l0-label-range-info grouping (for WSON only models) or the flexi-grid-label-range-info grouping (for DWDM flexible-grid only models) or the wdm-label-range-info grouping (for models that supports both WSON and DWDM flexible-grid). Each entry in the label-restriction list represents either the range of the available central wavelength values (in case of CWDM fixed-grid) or the range of the available nominal central frequencies values (in case of DWDM fixed or flexible grids): the grid-type attribute defines the type of grid for each entry of the list. In case of DWDM flexible grid, each entry in the label-restriction list represents also the range of the supported slot width values based on the following attributes, defined based on concepts used in : slot-width-granularity, which represents the minimum space between slot widths; min-slot-width-factor: a multiplier of the slot width granularity, indicating the minimum slot width supported by each entry in the label-restriction list; max-slot-width-factor: a multiplier of the slot width granularity, indicating the maximum slot width supported by each entry in the label-restriction list. Each entry of the label-restriction list, as defined in , defines a label-start, a label-end, a label-step and a range-bitmap. The label-start and label-end definitions, when used for representing WDM labe range, are augmented with WDM technology-specific attributes, using the wson-label-start-end grouping (for WSON only models) or the flexi-grid-label-start-end grouping (for DWDM flexible-grid only models) or the wdm-label-start-end grouping (for models that supports both WSON and DWDM flexible-grid). The label-step definition, when used for representing WDM labe range, are augmented with WDM technology-specific attributes, using the wson-label-step grouping (for WSON only models) or the flexi-grid-label-step grouping (for DWDM flexible-grid only models) or the wdm-label-step grouping (for models that supports both WSON and DWDM flexible-grid). The label-step definition for WDM depends on the WDM grid type: For CWDM and DWDM fixed grids, it describes the channel spacing, as defined in ; For DWDM flexible grids, it describes the nominal central frequency granularity (e.g., 6,25 GHz) as well as the multiplier for the supported values of n, as defined in .

YANG Module for Layer 0 Types This YANG module references , , , , , , , , , , , , , , , , , and .

WG List: Editor: Dieter Beller Editor: Sergio Belotti Editor: Italo Busi Editor: Haomian Zheng "; description "This module defines Optical Layer 0 types. This module provides groupings that can be applicable to Layer 0 Fixed Optical Networks (e.g., CWDM (Coarse Wavelength Division Multiplexing) and DWDM (Dense Wavelength Division Multiplexing)) and flexi-grid optical networks. Copyright (c) 2024 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Revised BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC XXXX; see the RFC itself for full legal notices. The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED', 'MAY', and 'OPTIONAL' in this document are to be interpreted as described in BCP 14 (RFC 2119) (RFC 8174) when, and only when, they appear in all capitals, as shown here."; // RFC Ed.: replace XXXX with actual RFC number and remove // this note // replace the revision date with the module publication date // the format is (year-month-day) revision 2024-11-27 { description "To be updated"; reference "RFC XXXX: A YANG Data Model for Layer 0 Types"; } revision 2021-08-13 { description "Initial version"; reference "RFC 9093: A YANG Data Model for Layer 0 Types"; } /* * Identities */ identity l0-grid-type { description "Layer 0 grid type"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC), Label Switching Routers, ITU-T G.694.2 (12/2003): Spectral grids for WDM applications: CWDM wavelength grid"; } identity wson-grid-cwdm { base l0-grid-type; description "CWDM grid"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.2 (12/2003): Spectral grids for WDM applications: CWDM wavelength grid"; } identity wson-grid-dwdm { base l0-grid-type; description "DWDM grid"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC), Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity flexi-grid-dwdm { base l0-grid-type; description "Flexi-grid"; reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity cwdm-ch-spc-type { description "CWDM channel-spacing type"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.2 (12/2003): Spectral grids for WDM applications: CWDM wavelength grid"; } identity cwdm-20nm { base cwdm-ch-spc-type; description "20nm channel spacing"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.2 (12/2003): Spectral grids for WDM applications: CWDM wavelength grid"; } identity dwdm-ch-spc-type { description "DWDM channel-spacing type"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity dwdm-100ghz { base dwdm-ch-spc-type; description "100 GHz channel spacing"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity dwdm-50ghz { base dwdm-ch-spc-type; description "50 GHz channel spacing"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity dwdm-25ghz { base dwdm-ch-spc-type; description "25 GHz channel spacing"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity dwdm-12p5ghz { base dwdm-ch-spc-type; description "12.5 GHz channel spacing"; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity flexi-ch-spc-type { status deprecated; description "Flexi-grid channel-spacing type"; } identity flexi-ch-spc-6p25ghz { base flexi-ch-spc-type; status deprecated; description "6.25 GHz channel spacing"; } identity flexi-ncfg-type { description "Flexi-grid Nominal Central Frequency Granularity (NCFG) type"; reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity flexi-ncfg-6p25ghz { base flexi-ncfg-type; description "6.25 GHz Nominal Central Frequency Granularity (NCFG)"; reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity flexi-slot-width-granularity { description "Flexi-grid slot width granularity"; reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity flexi-swg-12p5ghz { base flexi-slot-width-granularity; description "12.5 GHz slot width granularity"; reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } identity modulation { description "base identity for modulation type"; } identity DPSK { base modulation; description "DPSK (Differential Phase Shift Keying) modulation"; } identity QPSK { base modulation; description "QPSK (Quadrature Phase Shift Keying) modulation"; } identity DP-QPSK { base modulation; description "DP-QPSK (Dual Polarization Quadrature Phase Shift Keying) modulation"; } identity QAM8 { base modulation; description "8QAM (8 symbols Quadrature Amplitude Modulation)"; } identity DP-QAM8 { base modulation; description "DP-QAM8 (8 symbols Dual Polarization Quadrature Amplitude Modulation)"; } identity QAM16 { base modulation; description "QAM16 (16 symbols Quadrature Amplitude Modulation)"; } identity DP-QAM16 { base modulation; description "DP-QAM16 (16 symbols Dual Polarization Quadrature Amplitude Modulation)"; } identity QAM32 { base modulation; description "QAM32 (32 symbols Quadrature Amplitude Modulation)"; } identity DP-QAM32 { base modulation; description "DP-QAM32 (32 symbols Dual Polarization Quadrature Amplitude Modulation)"; } identity QAM64 { base modulation; description "QAM64 (64 symbols Quadrature Amplitude Modulation)"; } identity DP-QAM64 { base modulation; description "DP-QAM64 (64 symbols Dual Polarization Quadrature Amplitude Modulation)"; } identity fec-type { description "Base identity from which specific FEC (Forward Error Correction) type identities are derived."; } identity g-fec { base fec-type; description "Generic Forward Error Correction (G-FEC)."; reference "ITU-T G.975 v2.0 (10/2000): Forward error correction for submarine systems."; } identity super-fec { base fec-type; description "Super Forward Error Correction (S-FEC)."; reference "ITU-T G.975.1 v1.2 (07/2013): Forward error correction for high bit-rate DWDM submarine systems."; } identity no-fec { base fec-type; description "No FEC"; } identity sc-fec { base fec-type; description "Staircase Forward Error Correction (SC-FEC)."; reference "Annex A of ITU-T G.709.2 v1.1 (09/2020):OTU4 long-reach interface."; } identity o-fec { base fec-type; description "Open Forward Error Correction (O-FEC) which reuses the Bose, Chaudhuri and Hocquenghem (BCH) FEC."; reference "Clause 16.4.4 of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN long-reach interfaces; Annex E of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN long-reach interfaces."; } identity c-fec { base fec-type; description "Concatenated FEC (C-FEC) that combines an outer Staircase Forward Error Correction (SC-FEC) code and an inner double-extended SD-FEC (128,119) Hamming code. More details are provided in clause 15/G.709.3 where it is called DSH instead of concatenated FEC."; reference "Annex A of ITU-T G.709.2 v1.1 (09/2020):OTU4 long-reach interface; Annex D of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN long-reach interfaces; Clause 15 of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN long-reach interfaces."; } identity line-coding { description "Base identity to defined the bit rate/line coding of optical tributary signals."; reference "Section 7.1.2 of ITU-T G.698.2 v3.0 (11/2018)."; } identity line-coding-NRZ-2p5G { base line-coding; description "The non return to zero (NRZ) bit rate/line coding used by the optical tributary signal class NRZ 2.5G"; reference "Section 3.2.6 of ITU-T G.959.1 v8.0 (07/2018)."; } identity line-coding-NRZ-OTU1 { base line-coding; description "The non return to zero (NRZ) bit rate/line coding used by the Optical channel Transport Unit order 1 (OTU1) optical tributary signals"; reference "Section 7.2.1.2 of ITU-T G.959.1 v8.0 (07/2018)."; } identity line-coding-NRZ-10G { description "The non return to zero (NRZ) bit rate/line coding used by the optical tributary signal class NRZ 10G"; reference "Section 3.2.7 of ITU-T G.959.1 v8.0 (07/2018)."; } identity line-coding-NRZ-OTU2 { base line-coding; description "The non return to zero (NRZ) bit rate/line coding used by the Optical channel Transport Unit order 2 (OTU2) optical tributary signals"; reference "Section 7.2.1.2 of ITU-T G.959.1 v8.0 (07/2018)."; } identity line-coding-OTL4.4-SC { base line-coding; description "The bit rate/line coding used by optical tributary signals carrying a 100G Optical Transport Unit order 4 (OTU4) with Staircase Forward Error Correction (SC FEC) from a group of four Optical Transport Lanes (OTL)."; reference "Section 3.2.1 of ITU-T G.698.2 v3.0 (11/2018)."; } identity line-coding-FOIC1.4-SC { base line-coding; description "The bit rate/line coding used by optical tributary signals carrying a FlexO Interface of order C1 with 4 lanes (FOIC1.1) with Staircase Forward Error Correction (SC FEC)."; reference "Section 3.2.1 of ITU-T G.698.2 v3.0 (11/2018)."; } identity wavelength-assignment { description "Wavelength selection base"; reference "RFC 7689: Signaling Extensions for Wavelength Switched Optical Networks"; } identity first-fit-wavelength-assignment { base wavelength-assignment; description "All the available wavelengths are numbered, and this WA (Wavelength Assignment) method chooses the available wavelength with the lowest index"; reference "RFC 7689: Signaling Extensions for Wavelength Switched Optical Networks"; } identity random-wavelength-assignment { base wavelength-assignment; description "This WA method chooses an available wavelength randomly"; reference "RFC 7689: Signaling Extensions for Wavelength Switched Optical Networks"; } identity least-loaded-wavelength-assignment { base wavelength-assignment; description "This WA method selects the wavelength that has the largest residual capacity on the most loaded link along the route (in multi-fiber networks)"; reference "RFC 7689: Signaling Extensions for Wavelength Switched Optical Networks"; } identity lower-first-wavelength-assignment { base wavelength-assignment; description "Allocate wavelengths in ascending order, beginning from the lowest frequency and progressing toward the highest frequency within the permissible frequency range."; } identity upper-first-wavelength-assignment { base wavelength-assignment; description "Allocate wavelengths in decending order, beginning from the highest frequency and progressing toward the lowest frequency within the permissible frequency range."; } identity type-power-mode { description "power equalization mode used within the OMS and its elements"; } identity power-spectral-density { base type-power-mode; description "all elements must use power spectral density (W/Hz)"; } identity carrier-power { base type-power-mode; description "all elements must use power (dBm)"; } identity switching-wson-lsc { base te-types:switching-lsc; description "Wavelength Switched Optical Network Lambda-Switch Capable (WSON-LSC)."; reference "Section 3 of RFC 7688: GMPLS OSPF Enhancement for Signal and Network Element Compatibility for Wavelength Switched Optical Networks"; } identity switching-flexi-grid-lsc { base te-types:switching-lsc; description "Flexi-grid Lambda-Switch Capable (Flexi-Grid-LSC)."; reference "Section 4.1 of RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } /* * Typedefs */ typedef dwdm-n { type int16; description "The given value 'N' is used to determine the nominal central frequency. The nominal central frequency, 'f', is defined by: f = 193100.000 GHz + N x channel spacing (measured in GHz), where 193100.000 GHz (193.100000 THz) is the ITU-T 'anchor frequency' for transmission over the DWDM grid, and where 'channel spacing' is defined by the dwdm-ch-spc-type."; reference "RFC6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } typedef cwdm-n { type int16; description "The given value 'N' is used to determine the nominal central wavelength. The nominal central wavelength is defined by: Wavelength = 1471 nm + N x channel spacing (measured in nm) where 1471 nm is the conventional 'anchor wavelength' for transmission over the CWDM grid, and where 'channel spacing' is defined by the cwdm-ch-spc-type."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.2 (12/2003): Spectral grids for WDM applications: CWDM wavelength grid"; } typedef flexi-n { type int16; description "The given value 'N' is used to determine the nominal central frequency. The nominal central frequency, 'f', is defined by: f = 193100.000 GHz + N x NCFG (measured in GHz), where 193100.000 GHz (193.100000 THz) is the ITU-T 'anchor frequency' for transmission over the DWDM grid, and where NCFG is defined by the flexi-ncfg-type, or by the deprecated flexi-ch-spc-type."; reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } typedef flexi-m { type uint16; description "The given value 'M' is used to determine the slot width. A slot width is defined by: slot width = M x SWG (measured in GHz), where SWG is defined by the flexi-slot-width-granularity."; reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers, ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } typedef standard-mode { type string; description "Identifies an ITU-T G.698.2 standard application code. It MUST be a string with a format that follows the nomenclature defined in section 5.3 of ITU-T G.698.2."; reference "ITU-T G.698.2 (11/2018)"; } typedef organization-identifier { type string; description "vendor/organization identifier that uses a private mode out of already defined in G.698.2 ITU-T application-code"; reference "Section 2.5.2 of RFC YYYY: A YANG Data Model for Optical Impairment-aware Topology."; } // RFC Ed.: replace YYYY with actual RFC number and remove // this note after draft-ietf-ccamp-optical-impairment-topology-yang // is published as an RFC typedef operational-mode { type string; description "Identifies an organization (e.g., vendor) specific mode. The format of the string has to be defined by the organization which is responsible for defining the corresponding optical interface specification."; reference "Section 2.5.2 of RFC YYYY: A YANG Data Model for Optical Impairment-aware Topology."; } // RFC Ed.: replace YYYY with actual RFC number and remove // this note after draft-ietf-ccamp-optical-impairment-topology-yang // is published as an RFC typedef frequency-thz { type decimal64 { fraction-digits 9; } units "THz"; description "The DWDM frequency in THz, e.g., 193.112500000"; } typedef frequency-ghz { type decimal64 { fraction-digits 6; } units "GHz"; description "The DWDM frequency in GHz, e.g., 193112.500000"; } typedef snr { type decimal-2; units "dB@0.1nm"; description "(Optical) Signal to Noise Ratio measured over 0.1 nm resolution bandwidth"; reference "ITU-T G.977.1 (02/2021): Transverse compatible dense wavelength division multiplexing applications for repeatered optical fibre submarine cable systems"; } typedef snr-or-null { type union { type snr; type empty; } description "(Optical) Signal to Noise Ratio measured over 0.1 nm resolution bandwidth, when known, or an empty value when unknown."; } typedef fiber-type { type enumeration { enum G.652 { description "G.652 Standard Singlemode Fiber"; } enum G.654 { description "G.654 Cutoff Shifted Fiber"; } enum G.653 { description "G.653 Dispersion Shifted Fiber"; } enum G.655 { description "G.655 Non-Zero Dispersion Shifted Fiber"; } enum G.656 { description "G.656 Non-Zero Dispersion for Wideband Optical Transport"; } enum G.657 { description "G.657 Bend-Insensitive Fiber"; } } description "ITU-T based fiber-types"; } typedef decimal-2 { type decimal64 { fraction-digits 2; } description "A decimal64 value with two digits."; } typedef decimal-2-or-null { type union { type decimal-2; type empty; } description "A decimal64 value with two digits, when the value is known or an empty value when the value is not known."; } typedef power-gain { type decimal-2 { range "0..max"; } units "dB"; description "The gain in dB."; } typedef power-gain-or-null { type union { type power-gain; type empty; } description "The gain in dB, when it is known or an empty value when the power gain/loss is not known."; } typedef power-loss { type decimal-2 { range "0..max"; } units "dB"; description "The power attenuation in dB."; } typedef power-loss-or-null { type union { type power-loss; type empty; } description "The power attenuation in dB, when it is known or an empty value when the loss is not known."; } typedef power-ratio { type decimal-2; units "dB"; description "The power difference in dB."; } typedef power-ratio-or-null { type union { type power-ratio; type empty; } description "The power difference in dB, when it is known or an empty value when the difference is not known."; } typedef power-dbm { type decimal-2; units "dBm"; description "The power in dBm."; } typedef power-dbm-or-null { type union { type power-dbm; type empty; } description "The power in dBm, when it is known or an empty value when the power is not known."; } typedef decimal-5 { type decimal64 { fraction-digits 5; } description "A decimal64 value with five digits."; } typedef decimal-5-or-null { type union { type decimal-5; type empty; } description "A decimal64 value with five digits, when the value is known or an empty value when the value is not known."; } typedef psd { type decimal64 { fraction-digits 16; } units "W/Hz"; description "The power spectral density (PSD). Typical value : 3.9 E-14, resolution 0.1nW/MHz."; reference "ITU-T G.9700 (07/2019): Fast access to subscriber terminals (G.fast) - Power spectral density specification"; } typedef psd-or-null { type union { type psd; type empty; } description "The power spectral density (PSD), when it is known or an empty value when the PSD is not known."; } typedef decimal-18 { type decimal64 { fraction-digits 18; } description "A decimal64 value with eighteen digits."; } typedef decimal-18-or-null { type union { type decimal-18; type empty; } description "A decimal64 value with eighteen digits, when the value is known or an empty value when the value is not known."; } /* * Groupings */ grouping wdm-label-start-end { description "The WDM label-start or label-end used to specify DWDM and CWDM label range."; choice grid-type { description "Label for fixed & flexi-DWDM or CWDM grid"; case fixed-dwdm { leaf dwdm-n { when "derived-from-or-self(../../../grid-type, \"wson-grid-dwdm\")" { description "Valid only when grid type is DWDM."; } type l0-types:dwdm-n; description "The given value 'N' is used to determine the nominal central frequency."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } case cwdm { leaf cwdm-n { when "derived-from-or-self(../../../grid-type, \"wson-grid-cwdm\")" { description "Valid only when grid type is CWDM."; } type l0-types:cwdm-n; description "The given value 'N' is used to determine the nominal central wavelength."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } case flexi-grid { uses l0-types:flexi-grid-label-start-end; } } reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } grouping wdm-label-step { description "Label step information for fixed & flexi-DWDM or CWDM grid"; choice l0-grid-type { description "Grid type: DWDM, CWDM, etc."; case fixed-dwdm { leaf wson-dwdm-channel-spacing { when "derived-from-or-self(../../grid-type, \"wson-grid-dwdm\")" { description "Valid only when grid type is DWDM."; } type identityref { base dwdm-ch-spc-type; } description "Label-step is the channel spacing (GHz), e.g., 100.000, 50.000, 25.000, or 12.500 GHz for DWDM."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } case cwdm { leaf wson-cwdm-channel-spacing { when "derived-from-or-self(../../grid-type, \"wson-grid-cwdm\")" { description "Valid only when grid type is CWDM."; } type identityref { base cwdm-ch-spc-type; } description "Label-step is the channel spacing (nm), i.e., 20 nm for CWDM, which is the only value defined for CWDM."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } case flexi-grid { uses flexi-grid-label-step; } } reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.2 (12/2003): Spectral grids for WDM applications: CWDM wavelength grid, RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } grouping wdm-label-hop { description "Generic label-hop information for fixed & flexi-DWDM or CWDM grid"; choice grid-type { description "Label for DWDM or CWDM grid"; case fixed-dwdm { choice fixed-single-or-super-channel { description "single or super channel"; case single { leaf dwdm-n { type l0-types:dwdm-n; description "The given value 'N' is used to determine the nominal central frequency."; } } case multi { leaf-list subcarrier-dwdm-n { type l0-types:dwdm-n; min-elements 2; description "The given values 'N' are used to determine the nominal central frequency for each subcarrier channel."; reference "ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } } } } case cwdm { leaf cwdm-n { type l0-types:cwdm-n; description "The given value 'N' is used to determine the nominal central wavelength."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } case flexi-grid { uses l0-types:flexi-grid-label-hop; } } reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } grouping wdm-label-range-info { description "WDM label range related information"; uses l0-label-range-info; container flexi-grid { when "derived-from-or-self(../grid-type, \"flexi-grid-dwdm\")" { description "Applicable only when the grid type is flexi-grid-dwdm."; } description "flexi-grid definition"; leaf slot-width-granularity { type identityref { base flexi-slot-width-granularity; } default "flexi-swg-12p5ghz"; description "Minimum space between slot widths. Default is 12.500 GHz."; reference "RFC 7698: Framework and Requirements for GMPLS-Based Control of Flexi-Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } leaf min-slot-width-factor { type uint16 { range "1..max"; } default "1"; description "A multiplier of the slot width granularity, indicating the minimum slot width supported by an optical port. Minimum slot width is calculated by: Minimum slot width (GHz) = min-slot-width-factor * slot-width-granularity."; reference "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi- Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } leaf max-slot-width-factor { type uint16 { range "1..max"; } must '. >= ../min-slot-width-factor' { error-message "Maximum slot width must be greater than or equal to minimum slot width."; } description "A multiplier of the slot width granularity, indicating the maximum slot width supported by an optical port. Maximum slot width is calculated by: Maximum slot width (GHz) = max-slot-width-factor * slot-width-granularity If specified, maximum slot width must be greater than or equal to minimum slot width. If not specified, maximum slot width is equal to minimum slot width."; reference "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi- Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } } } grouping wson-label-start-end { description "The WSON label-start or label-end used to specify WSON label range."; choice grid-type { description "Label for DWDM or CWDM grid"; case dwdm { leaf dwdm-n { when "derived-from-or-self(../../../grid-type, \"wson-grid-dwdm\")" { description "Valid only when grid type is DWDM."; } type l0-types:dwdm-n; description "The central frequency of DWDM."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } case cwdm { leaf cwdm-n { when "derived-from-or-self(../../../grid-type, \"wson-grid-cwdm\")" { description "Valid only when grid type is CWDM."; } type l0-types:cwdm-n; description "Channel wavelength computing input."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } } reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } grouping wson-label-hop { description "Generic label-hop information for WSON"; choice grid-type { description "Label for DWDM or CWDM grid"; case dwdm { choice single-or-super-channel { description "single or super channel"; case single { leaf dwdm-n { type l0-types:dwdm-n; description "The given value 'N' is used to determine the nominal central frequency."; } } case super { leaf-list subcarrier-dwdm-n { type l0-types:dwdm-n; description "The given values 'N' are used to determine the nominal central frequency for each subcarrier channel."; reference "ITU-T G.694.1 (10/2020): Spectral grids for WDM applications: DWDM frequency grid"; } } } } case cwdm { leaf cwdm-n { type l0-types:cwdm-n; description "The given value 'N' is used to determine the nominal central wavelength."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } } reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } grouping l0-label-range-info { description "Information about Layer 0 label range."; leaf grid-type { type identityref { base l0-grid-type; } description "Grid type"; } leaf priority { type uint8; description "Priority in Interface Switching Capability Descriptor (ISCD)."; reference "RFC 4203: OSPF Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS)"; } reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } grouping wson-label-step { description "Label step information for WSON"; choice l0-grid-type { description "Grid type: DWDM, CWDM, etc."; case dwdm { leaf wson-dwdm-channel-spacing { when "derived-from-or-self(../../grid-type, \"wson-grid-dwdm\")" { description "Valid only when grid type is DWDM."; } type identityref { base dwdm-ch-spc-type; } description "Label-step is the channel spacing (GHz), e.g., 100.000, 50.000, 25.000, or 12.500 GHz for DWDM."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } case cwdm { leaf wson-cwdm-channel-spacing { when "derived-from-or-self(../../grid-type, \"wson-grid-cwdm\")" { description "Valid only when grid type is CWDM."; } type identityref { base cwdm-ch-spc-type; } description "Label-step is the channel spacing (nm), i.e., 20 nm for CWDM, which is the only value defined for CWDM."; reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers"; } } } reference "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC) Label Switching Routers, ITU-T G.694.2 (12/2003): Spectral grids for WDM applications: CWDM wavelength grid"; } grouping flexi-grid-label-start-end { description "The flexi-grid label-start or label-end used to specify flexi-grid label range."; leaf flexi-n { type l0-types:flexi-n; description "The given value 'N' is used to determine the nominal central frequency. As described in section 3.1 of RFC 8363, the range of available nominal central frequencies are advertised for m=1, which means that for an available central frequency n, the frequency slot from central frequency n-1 to central frequency n+1 is available."; } reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers, RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } grouping flexi-grid-frequency-slot { description "Flexi-grid frequency slot grouping."; uses flexi-grid-label-start-end; leaf flexi-m { type l0-types:flexi-m; description "The given value 'M' is used to determine the slot width."; } reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers"; } grouping flexi-grid-label-hop { description "Generic label-hop information for flexi-grid"; choice single-or-super-channel { description "single or super channel"; case single { uses flexi-grid-frequency-slot; } case super { status deprecated; list subcarrier-flexi-n { key "flexi-n"; status deprecated; uses flexi-grid-frequency-slot { status deprecated; } description "List of subcarrier channels for flexi-grid super channel."; } } case multi { container frequency-slots { description "The top level container for the list of frequency slots used for flexi-grid super channel."; list frequency-slot { key "flexi-n"; min-elements 2; uses flexi-grid-frequency-slot; description "List of frequency slots used for flexi-grid super channel."; } } } } reference "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } grouping flexi-grid-label-range-info { description "Flexi-grid-specific label range related information"; uses l0-label-range-info; container flexi-grid { description "flexi-grid definition"; leaf slot-width-granularity { type identityref { base flexi-slot-width-granularity; } default "flexi-swg-12p5ghz"; description "Minimum space between slot widths. Default is 12.500 GHz."; reference "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } leaf min-slot-width-factor { type uint16 { range "1..max"; } default "1"; description "A multiplier of the slot width granularity, indicating the minimum slot width supported by an optical port. Minimum slot width is calculated by: Minimum slot width (GHz) = min-slot-width-factor * slot-width-granularity."; reference "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi- Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } leaf max-slot-width-factor { type uint16 { range "1..max"; } must '. >= ../min-slot-width-factor' { error-message "Maximum slot width must be greater than or equal to minimum slot width."; } description "A multiplier of the slot width granularity, indicating the maximum slot width supported by an optical port. Maximum slot width is calculated by: Maximum slot width (GHz) = max-slot-width-factor * slot-width-granularity If specified, maximum slot width must be greater than or equal to minimum slot width. If not specified, maximum slot width is equal to minimum slot width."; reference "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi- Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } } } grouping flexi-grid-label-step { description "Label step information for flexi-grid"; leaf flexi-grid-channel-spacing { type identityref { base flexi-ch-spc-type; } default "flexi-ch-spc-6p25ghz"; status deprecated; description "Label-step is the nominal central frequency granularity (GHz), e.g., 6.25 GHz."; reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers"; } leaf flexi-ncfg { type identityref { base flexi-ncfg-type; } default "flexi-ncfg-6p25ghz"; description "Label-step is the nominal central frequency granularity (GHz), e.g., 6.25 GHz."; reference "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda Switch Capable (LSC) Label Switching Routers"; } leaf flexi-n-step { type uint8; description "This attribute defines the multiplier for the supported values of 'N'. For example, given a grid with a nominal central frequency granularity of 6.25 GHz, the granularity of the supported values of the nominal central frequency could be 12.5 GHz. In this case, the values of flexi-n should be even and this constraint is reported by setting the flexi-n-step to 2. This attribute is also known as central frequency granularity in RFC 8363."; reference "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid Dense Wavelength Division Multiplexing (DWDM) Networks"; } } grouping transceiver-mode { description "This grouping is intended to be used for reporting the information of a transceiver's mode. The attributes for the explicit mode shall be augmented when used with either: - the proper leafrefs, when explicit mode templates are used; or, - the explicit-mode grouping, when explicit mode templates are not used. The compatible-modes container shall be augmented with the proper leafrefs when used: see for example the transceiver-capabilities grouping below."; choice mode { config false; mandatory true; description "Indicates whether the transceiver's mode is a standard mode, an organizational mode or an explicit mode."; case G.698.2 { uses standard-mode; uses common-standard-organizational-mode; uses common-all-modes; } case organizational-mode { container organizational-mode { config false; description "The set of attributes for an organizational mode"; uses organizational-mode; uses common-standard-organizational-mode; uses common-all-modes; } // container organizational-mode } case explicit-mode { container explicit-mode { config false; description "The set of attributes for an explicit mode"; // uses explicit-mode; uses common-all-modes; container compatible-modes { description "Container for all the standard and organizational modes supported by the transceiver's explicit mode."; } // container compatible-modes } // container explicit-mode } // end of case explicit-mode } // end of choice } grouping transceiver-capabilities { description "This grouping is intended to be used for reporting the capabilities of a transceiver. The attributes for the explicit mode shall be augmented when used with either: - the proper leafrefs, when explicit mode templates are used; or, - the explicit-mode grouping, when explicit mode templates are not used."; container supported-modes { presence "When present, it indicates that the modes supported by a transceiver are reported."; config false; description "The top level container for the list supported transceiver's modes."; list supported-mode { key "mode-id"; config false; min-elements 1; description "The list of supported transceiver's modes."; leaf mode-id { type string { length "1..255"; } description "ID for the supported transceiver's mode."; } uses transceiver-mode { augment "mode/explicit-mode/explicit-mode/" + "compatible-modes" { description "Augments the compatible modes with the proper leafrefs."; leaf-list supported-application-codes { type leafref { path "../../../../supported-mode/mode-id"; } must "../../../../" + "supported-mode[mode-id=current()]/" + "standard-mode" { description "The pointer is only for application codes supported by transceiver."; } description "List of pointers to the application codes supported by the transceiver's explicit mode."; } leaf-list supported-organizational-modes { type leafref { path "../../../../supported-mode/mode-id"; } must "../../../../" + "supported-mode[mode-id=current()]/" + "organizational-mode" { description "The pointer is only for organizational modes supported by transceiver."; } description "List of pointers to the organizational modes supported by the transceiver's explicit mode."; } } } } // list supported-modes } // container supported-modes } // grouping transceiver-capabilities grouping standard-mode { description "ITU-T G.698.2 standard mode that guarantees interoperability. It must be an string with the following format: B-DScW-ytz(v) where all these attributes are conformant to the ITU-T recomendation"; leaf standard-mode { type standard-mode; config false; description "G.698.2 standard mode"; } } grouping organizational-mode { description "Transponder operational mode supported by organizations or vendor"; leaf operational-mode { type operational-mode; config false; description "configured organization- or vendor-specific application identifiers (AI) supported by the transponder"; } leaf organization-identifier { type organization-identifier; config false; description "organization identifier that uses organizational mode"; } } grouping penalty-value { description "A common definition of the penalty value used for describing multiple penalty types (.e.g, CD, PMD, PDL)."; leaf penalty-value { type union { type decimal-2 { range "0..max"; } type empty; } units "dB"; config false; mandatory true; description "The OSNR penalty associated with the related optical impairment at the receiver, when the value is known or an empty value when the value is not known."; } } grouping explicit-mode { description "Attributes capabilities related to explicit transceiver's mode. This grouping also contains the list of attributes related to optical impairment limits for explicit mode (min OSNR, max PMD, max CD, max PDL, Q-factor limit, etc.). In case of standard and operational mode the attributes are implicit."; leaf line-coding-bitrate { type identityref { base line-coding; } config false; description "Bit rate/line coding of the optical tributary signal."; reference "ITU-T G.698.2 section 7.1.2"; } leaf bitrate { type uint16; units "Gbit/sec"; config false; description "The gross bitrate (e.g., 100, 200) of the optical tributary signal."; } leaf max-diff-group-delay { type decimal-2; units "ps"; config false; description "Maximum Differential group delay of this mode for this lane"; } leaf max-chromatic-dispersion { type decimal-2 { range "0..max"; } units "ps/nm"; config false; description "Maximum acceptable accumulated chromatic dispersion (CD) on the receiver"; } list cd-penalty { key cd-value; config false; description "Optional penalty associated with a given accumulated chromatic dispersion (CD) value. This list of pair CD and penalty values can be used to sample the function penalty = f(CD)."; leaf cd-value { type decimal-2; units "ps/nm"; config false; mandatory true; description "The Chromatic Dispersion (CD)."; } uses penalty-value; } leaf max-polarization-mode-dispersion { type decimal-2 { range "0..max"; } units "ps"; config false; description "Maximum acceptable accumulated polarization mode dispersion (PMD) on the receiver"; reference "ITU-T G.666 (02/2011): Characteristics of polarization mode dispersion compensators and of receivers that compensate for polarization mode dispersion"; } list pmd-penalty { key pmd-value; config false; description "Optional penalty associated with a given accumulated polarization mode dispersion (PMD) value. This list of pair PMD and penalty can be used to sample the function penalty = f(PMD)."; leaf pmd-value { type decimal-2 { range "0..max"; } units "ps"; config false; mandatory true; description "The Polarization Mode Dispersion (PMD)."; } uses penalty-value; } leaf max-polarization-dependent-loss { type power-loss-or-null; config false; mandatory true; description "Maximum acceptable accumulated accumulated polarization dependent loss (PDL) on the receiver"; } list pdl-penalty { key pdl-value; config false; description "Optional penalty associated with a given accumulated polarization dependent loss (PDL) value. This list of pair PDL and penalty values can be used to sample the function PDL = f(penalty)."; leaf pdl-value { type power-loss; config false; mandatory true; description "Maximum acceptable accumulated polarization dependent loss (PDL)."; } uses penalty-value; } leaf available-modulation-type { type identityref { base modulation; } config false; description "Modulation type the specific transceiver in the list can support"; } leaf min-OSNR { type snr; units "dBm"; config false; description "min OSNR measured over 0.1 nm resolution bandwidth: if received OSNR at Rx-power reference point (rx-ref-channel-power) is lower than MIN-OSNR, an increased level of bit-errors post-FEC needs to be expected"; } leaf rx-ref-channel-power { type power-dbm; config false; description "The channel power used as reference for defining penalties and min-OSNR"; } list rx-channel-power-penalty { key rx-channel-power-value; config false; description "Optional penalty associated with a received power lower than rx-ref-channel-power. This list of pair power and penalty can be used to sample the function penalty = f(rx-channel-power)."; leaf rx-channel-power-value { type power-dbm; units "dBm"; config false; mandatory true; description "The Received Power."; } uses penalty-value; } leaf min-Q-factor { type decimal-2; units "dB"; config false; description "min Qfactor at FEC threshold"; } leaf available-baud-rate { type decimal64 { fraction-digits 1; } units "Bd"; config false; description "Baud-rate the specific transceiver in the list can support. Baud-rate is the unit for symbol rate or modulation rate in symbols per second or pulses per second. It is the number of distinct symbol changes (signal events) made to the transmission medium per second in a digitally modulated signal or a line code"; } leaf roll-off { type decimal64 { fraction-digits 4; range "0..1"; } config false; description "the roll-off factor (beta with values from 0 to 1) identifies how the real signal shape exceed the baud rate. If=0 it is exactly matching the baud rate.If=1 the signal exceeds the 50% of the baud rate at each side."; } leaf min-carrier-spacing { type frequency-ghz; config false; description "This attribute specifies the minimum nominal difference between the carrier frequencies of two homogeneous OTSis (which have the same optical characteristics but the central frequencies) such that if they are placed next to each other the interference due to spectrum overlap between them can be considered negligible. In case of heterogeneous OTSi it is up to path computation engine to determine the minimum distance between the carrier frequency of the two adjacent OTSi."; } leaf available-fec-type { type identityref { base fec-type; } config false; description "Available FEC"; } leaf fec-code-rate { type decimal64 { fraction-digits 8; range "0..max"; } config false; description "FEC-code-rate"; } leaf fec-threshold { type decimal64 { fraction-digits 8; range "0..max"; } config false; description "Threshold on the BER, for which FEC is able to correct errors"; } leaf in-band-osnr { type snr; config false; description "The OSNR defined within the bandwidth of the transmit spectral excursion (i.e., between the nominal central frequency of the channel and the -3.0dB points of the transmitter spectrum furthest from the nominal central frequency) measured at reference point Ss. The in-band OSNR is referenced to an optical bandwidth of 0.1nm @ 193.7 THz or 12.5 GHz."; reference "OIF-400ZR-01.0: Implementation Agreement 400ZR"; } leaf out-of-band-osnr { type snr; config false; description "The ratio of the peak transmitter power to the integrated power outside the transmitter spectral excursion. The spectral resolution of the measurement shall be better than the maximum spectral width of the peak. The out-of-band OSNR is referenced to an optical bandwidth of 0.1nm @ 193.7 THz or 12.5 GHz"; reference "OIF-400ZR-01.0: Implementation Agreement 400ZR"; } leaf tx-polarization-power-difference { type power-ratio; config false; description "The transmitter polarization dependent power difference defined as the power difference between X and Y polarizations"; reference "OIF-400ZR-01.0: Implementation Agreement 400ZR"; } leaf polarization-skew { type decimal-2; units "ps"; config false; description "The X-Y skew, included as a fixed value in the receiver polarization mode dispersion (PMD) tolerance limits."; reference "OIF-400ZR-01.0: Implementation Agreement 400ZR"; } } // grouping explicit-mode grouping common-standard-organizational-mode { description "Common attributes used by standard and organizational transceiver's modes."; leaf-list line-coding-bitrate { type identityref { base line-coding; } config false; description "The list of the bit rate/line coding of the optical tributary signal supported by the transceiver. Reporting this list is optional when the standard or organization mode supports only one bit rate/line coding."; reference "ITU-T G.698.2 section 7.1.2"; } } // grouping common-standard-organizational-mode grouping transmitter-tuning-range { description "Transmitter tuning range (f_tx-min, f_tx-max)"; leaf min-central-frequency { type frequency-thz; description "This parameter indicates the minimum frequency for the transmitter tuning range."; } leaf max-central-frequency { type frequency-thz; description "This parameter indicates the maximum frequency for the transmitter tuning range."; } leaf transceiver-tunability { type frequency-ghz; description "This parameter indicates the transmitter frequency fine tuning steps e.g 3.125GHz or 0.001GHz."; } } // grouping transmitter-tuning-range grouping common-all-modes { description "Common attributes used by all transceiver's modes."; container transmitter-tuning-range { config false; description "Transmitter tuning range (f_tx-min, f_tx-max)"; uses transmitter-tuning-range; } /* Alternative solution (not future safe): uses transmitter-tuning-range { refine min-central-frequency { config false; } refine max-central-frequency { config false; } refine transceiver-tunability { config false; } } */ leaf tx-channel-power-min { type power-dbm; config false; description "The minimum output power of this interface"; } leaf tx-channel-power-max { type power-dbm; config false; description "The maximum output power of this interface"; } leaf rx-channel-power-min { type power-dbm; config false; description "The minimum input power of this interface"; } leaf rx-channel-power-max { type power-dbm; config false; description "The maximum input power of this interface"; } leaf rx-total-power-max { type power-dbm; config false; description "Maximum rx optical power for all the channels. It is applicable only to multi-channel modes."; } } // grouping common-all-modes grouping common-transceiver-param { description "The common parameters of an optical transceiver, that supplement the configured mode."; uses common-transceiver-configured-param; uses common-transceiver-readonly-param; } grouping common-transceiver-configured-param { description "The configured parameters of an optical transceiver, that supplement the configured mode."; leaf line-coding-bitrate { type identityref { base line-coding; } description "Bit rate/line coding of the optical tributary signal. Support of this attribute is optional when the configured mode supports only one bit rate/line coding."; reference "ITU-T G.698.2 section 7.1.2"; } leaf tx-channel-power { type power-dbm-or-null; description "The current channel transmit power, when the value is known or an empty value when the value is not known. The empty value MUST NOT be used when this attribute is configured."; } } // grouping for configured transceiver attributes out of mode grouping common-transceiver-readonly-param { description "The common read-only parameters of an optical transceiver, that supplement the configured mode."; leaf rx-channel-power { type power-dbm-or-null; config false; description "The current channel received power, when the value is known or an empty value when the value is not known."; } leaf rx-total-power { type power-dbm-or-null; config false; description "The current total received power, when the value is known or an empty value when the value is not known."; } } // grouping for read-only transceiver attributes out of mode grouping l0-tunnel-attributes { description "Parameters for Layer0 (WSON or Flexi-Grid) Tunnels."; leaf wavelength-assignment { type identityref { base wavelength-assignment; } description "Wavelength Allocation Method"; } } grouping frequency-range { description "This grouping defines the lower and upper bounds of a frequency range (e.g., a band). This grouping SHOULD NOT be used to define a frequency slot, which SHOULD be defined using the n and m values instead."; leaf lower-frequency { type frequency-thz; mandatory true; description "The lower frequency boundary of the frequency range."; } leaf upper-frequency { type frequency-thz; must '. > ../lower-frequency' { error-message "The upper frequency must be greater than the lower frequency."; } mandatory true; description "The upper frequency boundary of the frequency range."; } } grouping l0-path-constraints { description "Common attribute for Layer 0 path constraints to be used by Layer 0 computation."; leaf gsnr-extra-margin { type snr { range 0..max; } default 0; description "An additional margin to be added to the OSNR-min of the transceiver when checking the estimated received Generalized SNR (GSNR)."; } } grouping l0-path-properties { description "Common attribute for reporting the Layer 0 computed path properties."; leaf estimated-gsnr { type snr; config false; description "The estimate received GSNR for the computed path."; } leaf estimated-eol-gsnr { type snr; config false; description "The estimate received GSNR for the computed path degraded at the end of life."; } leaf estimated-lowest-gsnr { type snr; config false; description "The estimate lowest received GSNR for the computed path among all possible wavelength channels along the same path."; } } } ]]>

Security Considerations This section is modeled after the template described in Section 3.7 of . The "ietf-layer0-types" YANG module define data models that are designed to be accessed via YANG-based management protocols, such as NETCONF and RESTCONF . These protocols have to use a secure transport layer (e.g., SSH , TLS , and QUIC ) and have to use mutual authentication. The Network Configuration Access Control Model (NACM) provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content. The YANG modules define a set of identities, types, and groupings. These nodes are intended to be reused by other YANG modules. The modules by themselves do not expose any data nodes that are writable, data nodes that contain read-only state, or RPCs. As such, there are no additional security issues related to the YANG module that need to be considered. Modules that use the groupings that are defined in this document should identify the corresponding security considerations. For example, reusing some of these groupings will expose privacy-related information (e.g., 'node-example').

IANA Considerations This document requests IANA to update the following URIs in the "IETF XML Registry" to refer to this document:

This document requests IANA to register the following YANG modules in the "YANG Module Names" registry within the "YANG Parameters" registry group.

• RFC Editor Note: Please replace XXXX with the RFC number assigned to this document and remove this note.

International Telecommunication Union International Telecommunication Union International Telecommunication Union International Telecommunication Union International Telecommunication Union International Telecommunication Union International Telecommunication Union International Telecommunication Union International Telecommunication Union International Telecommunication Union International Telecommunication Union International Telecommunication Union Optical Internetworking Forum YANG is a data modeling language used to model configuration data, state data, Remote Procedure Calls, and notifications for network management protocols. This document describes the syntax and semantics of version 1.1 of the YANG language. YANG version 1.1 is a maintenance release of the YANG language, addressing ambiguities and defects in the original specification. There are a small number of backward incompatibilities from YANG version 1. This document also specifies the YANG mappings to the Network Configuration Protocol (NETCONF). The Network Configuration Protocol (NETCONF) defined in this document provides mechanisms to install, manipulate, and delete the configuration of network devices. It uses an Extensible Markup Language (XML)-based data encoding for the configuration data as well as the protocol messages. The NETCONF protocol operations are realized as remote procedure calls (RPCs). This document obsoletes RFC 4741. [STANDARDS-TRACK] To allow efficient allocation of optical spectral bandwidth for systems that have high bit-rates, the International Telecommunication Union Telecommunication Standardization Sector (ITU-T) has extended its Recommendations G.694.1 and G.872 to include a new Dense Wavelength Division Multiplexing (DWDM) grid by defining a set of nominal central frequencies, channel spacings, and the concept of the "frequency slot". In such an environment, a data-plane connection is switched based on allocated, variable-sized frequency ranges within the optical spectrum, creating what is known as a flexible grid (flexi-grid). Given the specific characteristics of flexi-grid optical networks and their associated technology, this document defines a framework and the associated control-plane requirements for the application of the existing GMPLS architecture and control-plane protocols to the control of flexi-grid DWDM networks. The actual extensions to the GMPLS protocols will be defined in companion documents. This document defines a collection of common data types and groupings in the YANG data modeling language. These derived common types and groupings are intended to be imported by modules that model Layer 0 optical Traffic Engineering (TE) configuration and state capabilities such as Wavelength Switched Optical Networks (WSONs) and flexi-grid Dense Wavelength Division Multiplexing (DWDM) networks. Datastores are a fundamental concept binding the data models written in the YANG data modeling language to network management protocols such as the Network Configuration Protocol (NETCONF) and RESTCONF. This document defines an architectural framework for datastores based on the experience gained with the initial simpler model, addressing requirements that were not well supported in the initial model. This document updates RFC 7950. In many standards track documents several words are used to signify the requirements in the specification. These words are often capitalized. This document defines these words as they should be interpreted in IETF documents. This document specifies an Internet Best Current Practices for the Internet Community, and requests discussion and suggestions for improvements. RFC 2119 specifies common key words that may be used in protocol specifications. This document aims to reduce the ambiguity by clarifying that only UPPERCASE usage of the key words have the defined special meanings. Huawei Futurewei Technologies Alef Edge Cisco Systems Inc. Individual This document defines a collection of common data types, identities, and groupings in YANG data modeling language. These derived common data types, identities and groupings are intended to be imported by other modules, e.g., those which model the Traffic Engineering (TE) configuration and state capabilities. This document obsoletes RFC 8776. Technology in the optical domain is constantly evolving, and, as a consequence, new equipment providing lambda switching capability has been developed and is currently being deployed. Generalized MPLS (GMPLS) is a family of protocols that can be used to operate networks built from a range of technologies including wavelength (or lambda) switching. For this purpose, GMPLS defined a wavelength label as only having significance between two neighbors. Global wavelength semantics are not considered. In order to facilitate interoperability in a network composed of next generation lambda-switch-capable equipment, this document defines a standard lambda label format that is compliant with the Dense Wavelength Division Multiplexing (DWDM) and Coarse Wavelength Division Multiplexing (CWDM) grids defined by the International Telecommunication Union Telecommunication Standardization Sector. The label format defined in this document can be used in GMPLS signaling and routing protocols. [STANDARDS-TRACK] GMPLS supports the description of optical switching by identifying entries in fixed lists of switchable wavelengths (called grids) through the encoding of lambda labels. Work within the ITU-T Study Group 15 has defined a finer-granularity grid, and the facility to flexibly select different widths of spectrum from the grid. This document defines a new GMPLS lambda label format to support this flexi-grid. This document updates RFCs 3471 and 6205 by introducing a new label format. This document provides extensions to Generalized Multiprotocol Label Switching (GMPLS) signaling for control of Wavelength Switched Optical Networks (WSONs). Such extensions are applicable in WSONs under a number of conditions including: (a) when optional processing, such as regeneration, must be configured to occur at specific nodes along a path, (b) where equipment must be configured to accept an optical signal with specific attributes, or (c) where equipment must be configured to output an optical signal with specific attributes. This document provides mechanisms to support distributed wavelength assignment with a choice of distributed wavelength assignment algorithms. Nokia Orange Nokia Individual Huawei Technologies In order to provision an optical connection through optical networks, a combination of path continuity, resource availability, and impairment constraints must be met to determine viable and optimal paths through the network. The determination of appropriate paths is known as Impairment-Aware Routing and Wavelength Assignment (IA-RWA) for WSON, while it is known as Impairment-Aware Routing and Spectrum Assignment (IA-RSA) for SSON. This document provides a YANG data model for the impairment-aware TE topology in optical networks. This document defines a YANG data model for representing, retrieving, and manipulating Traffic Engineering (TE) Topologies. The model serves as a base model that other technology-specific TE topology models can augment. This document specifies encoding of extensions to the OSPF routing protocol in support of Generalized Multi-Protocol Label Switching (GMPLS). [STANDARDS-TRACK] The International Telecommunication Union Telecommunication standardization sector (ITU-T) has extended its Recommendations G.694.1 and G.872 to include a new Dense Wavelength Division Multiplexing (DWDM) grid by defining channel spacings, a set of nominal central frequencies, and the concept of the "frequency slot". Corresponding techniques for data-plane connections are known as "flexi-grid". Based on the characteristics of flexi-grid defined in G.694.1 and in RFCs 7698 and 7699, this document describes the Open Shortest Path First - Traffic Engineering (OSPF-TE) extensions in support of GMPLS control of networks that include devices that use the new flexible optical grid. This document provides Generalized Multiprotocol Label Switching (GMPLS) Open Shortest Path First (OSPF) routing enhancements to support signal compatibility constraints associated with Wavelength Switched Optical Network (WSON) elements. These routing enhancements are applicable in common optical or hybrid electro-optical networks where not all the optical signals in the network are compatible with all network elements participating in the network. This compatibility constraint model is applicable to common optical or hybrid electro-optical systems such as optical-electronic-optical (OEO) switches, regenerators, and wavelength converters, since such systems can be limited to processing only certain types of WSON signals. This document describes extensions to Multi-Protocol Label Switching (MPLS) signaling required to support Generalized MPLS. Generalized MPLS extends the MPLS control plane to encompass time-division (e.g., Synchronous Optical Network and Synchronous Digital Hierarchy, SONET/SDH), wavelength (optical lambdas) and spatial switching (e.g., incoming port or fiber to outgoing port or fiber). This document presents a functional description of the extensions. Protocol specific formats and mechanisms, and technology specific details are specified in separate documents. [STANDARDS-TRACK] The standardization of network configuration interfaces for use with the Network Configuration Protocol (NETCONF) or the RESTCONF protocol requires a structured and secure operating environment that promotes human usability and multi-vendor interoperability. There is a need for standard mechanisms to restrict NETCONF or RESTCONF protocol access for particular users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content. This document defines such an access control model. This document obsoletes RFC 6536. YANG is a data modeling language used to model configuration and state data manipulated by the Network Configuration Protocol (NETCONF), NETCONF remote procedure calls, and NETCONF notifications. [STANDARDS-TRACK] International Telecommunication Union This document provides a framework for applying Generalized Multi-Protocol Label Switching (GMPLS) and the Path Computation Element (PCE) architecture to the control of Wavelength Switched Optical Networks (WSONs). In particular, it examines Routing and Wavelength Assignment (RWA) of optical paths. This document focuses on topological elements and path selection constraints that are common across different WSON environments; as such, it does not address optical impairments in any depth. This document is not an Internet Standards Track specification; it is published for informational purposes. This document provides a model of information needed by the Routing and Wavelength Assignment (RWA) process in Wavelength Switched Optical Networks (WSONs). The purpose of the information described in this model is to facilitate constrained optical path computation in WSONs. This model takes into account compatibility constraints between WSON signal attributes and network elements but does not include constraints due to optical impairments. Aspects of this information that may be of use to other technologies utilizing a GMPLS control plane are discussed. A Wavelength Switched Optical Network (WSON) requires certain key information fields be made available to facilitate path computation and the establishment of Label Switched Paths (LSPs). The information model described in "Routing and Wavelength Assignment Information Model for Wavelength Switched Optical Networks" (RFC 7446) shows what information is required at specific points in the WSON. Part of the WSON information model contains aspects that may be of general applicability to other technologies, while other parts are specific to WSONs. This document provides efficient, protocol-agnostic encodings for the WSON-specific information fields. It is intended that protocol- specific documents will reference this memo to describe how information is carried for specific uses. Such encodings can be used to extend GMPLS signaling and routing protocols. In addition, these encodings could be used by other mechanisms to convey this same information to a Path Computation Element (PCE). YumaWorks Orange Huawei This memo provides guidelines for authors and reviewers of specifications containing YANG modules, including IANA-maintained modules. Recommendations and procedures are defined, which are intended to increase interoperability and usability of Network Configuration Protocol (NETCONF) and RESTCONF protocol implementations that utilize YANG modules. This document obsoletes RFC 8407. Also, this document updates RFC 8126 by providing additional guidelines for writing the IANA considerations for RFCs that specify IANA-maintained modules. The document also updates RFC 6020 by clarifying how modules and their revisions are handled by IANA. This document describes an HTTP-based protocol that provides a programmatic interface for accessing data defined in YANG, using the datastore concepts defined in the Network Configuration Protocol (NETCONF). The Secure Shell Protocol (SSH) is a protocol for secure remote login and other secure network services over an insecure network. This document describes the SSH authentication protocol framework and public key, password, and host-based client authentication methods. Additional authentication methods are described in separate documents. The SSH authentication protocol runs on top of the SSH transport layer protocol and provides a single authenticated tunnel for the SSH connection protocol. [STANDARDS-TRACK] This document specifies version 1.3 of the Transport Layer Security (TLS) protocol. TLS allows client/server applications to communicate over the Internet in a way that is designed to prevent eavesdropping, tampering, and message forgery. This document updates RFCs 5705 and 6066, and obsoletes RFCs 5077, 5246, and 6961. This document also specifies new requirements for TLS 1.2 implementations. This document defines the core of the QUIC transport protocol. QUIC provides applications with flow-controlled streams for structured communication, low-latency connection establishment, and network path migration. QUIC includes security measures that ensure confidentiality, integrity, and availability in a range of deployment circumstances. Accompanying documents describe the integration of TLS for key negotiation, loss detection, and an exemplary congestion control algorithm. This document describes an IANA maintained registry for IETF standards which use Extensible Markup Language (XML) related items such as Namespaces, Document Type Declarations (DTDs), Schemas, and Resource Description Framework (RDF) Schemas. This document captures the current syntax used in YANG module tree diagrams. The purpose of this document is to provide a single location for this definition. This syntax may be updated from time to time based on the evolution of the YANG language.

The Complete Schema Trees This appendix presents the complete tree of the Layer 0 Types data model. See for an explanation of the symbols used. The data type of every leaf node is shown near the right end of the corresponding line.

../../../../supported-mode/mode-id +--ro supported-organizational-modes* -> ../../../../supported-mode/mode-id grouping standard-mode: +--ro standard-mode? standard-mode grouping organizational-mode: +--ro operational-mode? operational-mode +--ro organization-identifier? organization-identifier grouping penalty-value: +--ro penalty-value union grouping explicit-mode: +--ro line-coding-bitrate? identityref +--ro bitrate? uint16 +--ro max-diff-group-delay? decimal-2 +--ro max-chromatic-dispersion? decimal-2 +--ro cd-penalty* [cd-value] | +--ro cd-value decimal-2 | +--ro penalty-value union +--ro max-polarization-mode-dispersion? decimal-2 +--ro pmd-penalty* [pmd-value] | +--ro pmd-value decimal-2 | +--ro penalty-value union +--ro max-polarization-dependent-loss power-loss-or-null +--ro pdl-penalty* [pdl-value] | +--ro pdl-value power-loss | +--ro penalty-value union +--ro available-modulation-type? identityref +--ro min-OSNR? snr +--ro rx-ref-channel-power? power-dbm +--ro rx-channel-power-penalty* [rx-channel-power-value] | +--ro rx-channel-power-value power-dbm | +--ro penalty-value union +--ro min-Q-factor? decimal-2 +--ro available-baud-rate? decimal64 +--ro roll-off? decimal64 +--ro min-carrier-spacing? frequency-ghz +--ro available-fec-type? identityref +--ro fec-code-rate? decimal64 +--ro fec-threshold? decimal64 +--ro in-band-osnr? snr +--ro out-of-band-osnr? snr +--ro tx-polarization-power-difference? power-ratio +--ro polarization-skew? decimal-2 grouping common-standard-organizational-mode: +--ro line-coding-bitrate* identityref grouping transmitter-tuning-range: +-- min-central-frequency? frequency-thz +-- max-central-frequency? frequency-thz +-- transceiver-tunability? frequency-ghz grouping common-all-modes: +--ro transmitter-tuning-range | +--ro min-central-frequency? frequency-thz | +--ro max-central-frequency? frequency-thz | +--ro transceiver-tunability? frequency-ghz +--ro tx-channel-power-min? power-dbm +--ro tx-channel-power-max? power-dbm +--ro rx-channel-power-min? power-dbm +--ro rx-channel-power-max? power-dbm +--ro rx-total-power-max? power-dbm grouping common-transceiver-param: +-- line-coding-bitrate? identityref +-- tx-channel-power? power-dbm-or-null +--ro rx-channel-power? power-dbm-or-null +--ro rx-total-power? power-dbm-or-null grouping common-transceiver-configured-param: +-- line-coding-bitrate? identityref +-- tx-channel-power? power-dbm-or-null grouping common-transceiver-readonly-param: +--ro rx-channel-power? power-dbm-or-null +--ro rx-total-power? power-dbm-or-null grouping l0-tunnel-attributes: +-- wavelength-assignment? identityref grouping frequency-range: +-- lower-frequency frequency-thz +-- upper-frequency frequency-thz grouping l0-path-constraints: +-- gsnr-extra-margin? snr grouping l0-path-properties: +--ro estimated-gsnr? snr +--ro estimated-eol-gsnr? snr +--ro estimated-lowest-gsnr? snr ]]>

Changes from RFC 9093 This version adds new identities, data types, and groupings to the 'ietf-layer0-types' YANG module. The following new YANG identities have been added to the 'ietf-layer0-types' module: cwdm-ch-spc-type flexi-ncfg-type flexi-ncfg-6p25gh modulation DPSK QPSK DP-QPSK QAM8 DP-QAM8 QAM16 DP-QAM16 QAM32 DP-QAM32 QAM64 DP-QAM64 fec-type g-fec super-fec no-fec sc-fec o-fec c-fec line-coding line-coding-NRZ-2p5G line-coding-NRZ-OTU1 line-coding-NRZ-10G line-coding-NRZ-OTU2 line-coding-OTL4.4-SC line-coding-FOIC1.4-SC wavelength-assignment first-fit-wavelength-assignment random-wavelength-assignment least-loaded-wavelength-assignment lower-first-wavelength-assignment upper-first-wavelength-assignment type-power-mode power-spectral-density carrier-power switching-wson-lsc switching-flexi-grid-lsc The following new YANG data types have been added to the 'ietf-layer0-types' module: Standard-mode Organization-identifier Operational-mode frequency-thz frequency-ghz snr snr-or-null fiber-type decimal-2 decimal-2-or-null power-gain power-gain-or-null power-loss power-loss-or-null power-ratio power-ratio-or-null power-dbm power-dbm-or-null decimal-5 decimal-5-or-null psd psd-or-null The following new YANG groupings have been added to the 'ietf-layer0-types' module: wdm-label-start-end wdm-label-step wdm-label-hop wdm-label-range-info transceiver-mode transceiver-capabilities standard-mode organizational-mode penalty-value explicit-mode common-standard-organizational-mode transmitter-tuning-range common-all-mode common-transceiver-param common-transceiver-configured-param common-transceiver-readonly-param l0-tunnel-attributes frequency-range l0-path-constraints l0-path-properties

Acknowledgments The authors and the working group give their sincere thanks to Robert Wilton for the YANG doctor review and to Adrian Farrel and Tom Petch for their comments during the model and document development. This document was prepared using kramdown.

Contributors Huawei

zhenghaomian@huawei.com

University of Lancaster

d.king@lancaster.ac.uk

Cisco

ggalimbe@cisco.com

Nokia

Enrico.Griseri@nokia.com

Huawei

dhruv.ietf@gmail.com

ETRI

byyun@etri.re.kr

CTTC

ricard.vilalta@cttc.es

Samsung

younglee.tx@gmail.com

Nokia

victor.lopez@nokia.com