]> 5}="yes"?> Retired

Vancouver, British Columbia Canada deering@noreply.ietf.org

Futurewei Technologies USA

USA tte@cs.fau.de

PIM This memo specifies the extensions required of a host implementation of the Internet Protocol (IP) to support Any Source Multicast (ASM) IP Multicasting or abbreviated IP Multicast. Distribution of this memo is unlimited. This document replaces for anything but its specification of the IGMP version 1 protocol.

STATUS OF THIS MEMO This memo specifies the extensions required of a host implementation of the Internet Protocol (IP) to support Any Source Multicast (ASM) IP Multicasting or abbreviated IP Multicast. Distribution of this memo is unlimited. This document replaces for anything but its specification of the IGMP version 1 protocol.

Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 when, and only when, they appear in all capitals, as shown here.

INTRODUCTION The host extensions defined in this memo are called Any Source Multicast (ASM) IP multicast or abbreviated IP multicast. The term Any Source Multicast is used to distinguish these extensions from Source Specific Multicast (SSM) IP multicast as defined by . The abbreviation IP multicast always refers to this memo's extensions. This memo applies to both IP and IPv6. When it uses the term IP it implies either or both version of the IP protocol. It uses the terms IP and/or IPv6 explicitly when referring to functions applicable to only a specific version of the IP protocol. This document replaces for anything but the specification of IGMP version 1 in Appendix I. of . See and for a detailled list of changes from that memo. IP multicasting is the transmission of an IP datagram to a "host group", a set of zero or more hosts identified by a single IP destination address. A multicast datagram is delivered to all members of its destination host group with the same "best-efforts" reliability as regular unicast IP datagrams, i.e., the datagram is not guaranteed to arrive intact at all members of the destination group or in the same order relative to other datagrams. The membership of a host group is dynamic; that is, hosts may join and leave groups at any time. There is no restriction on the location or number of members in a host group. A host may be a member of more than one group at a time. A host need not be a member of a group to send datagrams to it. A host group may be permanent or transient. A permanent group has a well-known, administratively assigned IP address. It is the address, not the membership of the group, that is permanent; at any time a permanent group may have any number of members, even zero. Those IP multicast addresses that are not reserved for permanent groups are available for dynamic assignment to transient groups which exist only as long as they have members. Internetwork forwarding of IP multicast datagrams is handled by "multicast routers" which may be co-resident with, or separate from, internet gateways. A host transmits an IP multicast datagram as a local network multicast which reaches all immediately-neighboring members of the destination host group. If the datagram has an IP time-to-live greater than 1, the multicast router(s) attached to the local network take responsibility for forwarding it towards all other networks that have members of the destination group. On those other member networks that are reachable within the IP time-to-live, an attached multicast router completes delivery by transmitting the datagram as a local multicast. This memo specifies the extensions required of a host IP implementation to support IP multicasting, where a "host" is any internet host or gateway other than those acting as multicast routers. The algorithms and protocols used within and between multicast routers are transparent to hosts and will be specified in separate documents. This memo also does not specify how local network multicasting is accomplished for all types of network, although it does specify the required service interface to an arbitrary local network and gives an Ethernet specification as an example. Specifications for other types of network will be the subject of future memos.

LEVELS OF CONFORMANCE There are three levels of conformance to this specification:

Level 0: no support for IP multicasting. There is, at this time, no requirement that all IP implementations support IP multicasting. Level 0 hosts will, in general, be unaffected by multicast activity. The only exception arises on some types of local network, where the presence of level 1 or 2 hosts may cause misdelivery of multicast IP datagrams to level 0 hosts. Such datagrams can easily be identified by the presence of a class D IP address in their destination address field; they SHOULD be quietly discarded by hosts that do not support IP multicasting. Class D addresses are described in section 4 of this memo.

Level 1: support for sending but not receiving multicast IP datagrams. Level 1 allows a host to partake of some multicast-based services, such as resource location or status reporting, but it does not allow a host to join any host groups. An IP implementation may be upgraded from level 0 to level 1 very easily and with little new code. Only sections 4, 5, and 6 of this memo are applicable to level 1 implementations.

Level 2: full support for IP multicasting. Level 2 allows a host to join and leave host groups, as well as send IP datagrams to host groups. Most IPv6 hosts require Level 2 support because IPv6 Neighbor Discovery (, as used on most link types) depends on multicast and requires that nodes join Solicited Node multicast addresses. Level 2 requires implementation of the Internet Group Management Protocol (IGMP) for IP and the equivalent Multicast Listener Discovery Protocol (MLD) for IPv6 and extension of the IP and local network service interfaces within the host. The current protocol versions for full support of IP multicasting are and or lightweight versions of either protocol . All of the following sections of this memo are applicable to level 2 implementations.

HOST GROUP ADDRESSES IP Host groups are identified by class D IP addresses, i.e., those with "1110" as their high-order four bits. Class E IP addresses, i.e., those with "1111" as their high-order four bits, are reserved for future addressing modes. In Internet standard "dotted decimal" notation, host group addresses range from 224.0.0.0 to 239.255.255.255. The address 224.0.0.0 is guaranteed not to be assigned to any group, and 224.0.0.1 is assigned to the permanent group of all IP hosts (including gateways). This is used to address all IP multicast hosts on the directly connected network. There is no multicast address (or any other IP address) for all hosts on the total Internet. The addresses of other well-known, permanent groups are to be published in "Assigned Numbers". IPv6 Host groups are identified by IPv6 addresses as defined in section 2.7 and updated by , . IP and IPv6 addresses as specified in are not used for ASM IP multicast and are not considered IP host groups. They are instead only the destination address part G of Source Specific Multicast (SSM) IP multicast (S,G) channels. Appendix I contains some background discussion of several issues related to host group addresses.

MODEL OF A HOST IP IMPLEMENTATION The multicast extensions to a host IP implementation are specified in terms of the layered model illustrated below in . In this model, ICMP/ICMPv6 and (for level 2 hosts) IGMP/MLD are considered to be implemented within the IP module, and the mapping of IP addresses to local network addresses is considered to be the responsibility of local network modules. This model is for expository purposes only, and should not be construed as constraining an actual implementation.

To provide level 1 multicasting, a host IP implementation MUST support the transmission of multicast IP datagrams. To provide level 2 multicasting, a host MUST also support the reception of multicast IP datagrams. Each of these two new services is described in a separate section, below. For each service, extensions are specified for the IP service interface, the IP module, the local network service interface, and an Ethernet local network module. Extensions to local network modules other than Ethernet are mentioned briefly, but are not specified in detail.

SENDING MULTICAST IP DATAGRAMS

Extensions to the IP Service Interface Multicast IP datagrams are sent using the same "Send IP" operation used to send unicast IP datagrams; an upper-layer protocol module merely specifies an IP host group address, rather than an individual IP address, as the destination. However, a number of extensions may be necessary or desirable. First, the service interface SHOULD provide a way for the upper-layer protocol to specify the IP time-to-live of an outgoing multicast datagram, if such a capability does not already exist. If the upper-layer protocol chooses not to specify a time-to-live, it SHOULD default to 1 for all multicast IP datagrams, so that an explicit choice is required to multicast beyond a single network. Second, for hosts that may be attached to more than one network, the service interface SHOULD provide a way for the upper-layer protocol to identify which network interface is be used for the multicast transmission. Only one interface is used for the initial transmission; multicast routers are responsible for forwarding to any other networks, if necessary. If the upper-layer protocol chooses not to identify an outgoing interface, a default interface SHOULD be used, preferably under the control of system management. Third (level 2 implementations only), for the case in which the host is itself a member of a group to which a datagram is being sent, the service interface SHOULD provide a way for the upper-layer protocol to inhibit local delivery of the datagram; by default, a copy of the datagram is looped back. This is a performance optimization for upper-layer protocols that restrict the membership of a group to one process per host (such as a routing protocol), or that handle loopback of group communication at a higher layer (such as a multicast transport protocol). IPv6 socket extensions supporting these functions are defined in , section 5.2.

Extensions to the IP Module To support the sending of multicast IP datagrams, the IP module MUST be extended to recognize IP host group addresses when routing outgoing datagrams. Most IP implementations include the following logic:

To allow multicast transmissions, the routing logic MUST be changed to:

If the sending host is itself a member of the destination group on the outgoing interface, a copy of the outgoing datagram MUST be looped-back for local delivery, unless inhibited by the sender. (Level 2 implementations only.) The IP source address of the outgoing datagram MUST be one of the individual addresses corresponding to the outgoing interface. A host group address MUST never be placed in the source address field or anywhere in a source route or record route option of an outgoing IP datagram. These packets are not IP Multicast packets but simply invalid packets.

Extensions to the Local Network Service Interface No change to the local network service interface is required to support the sending of multicast IP datagrams. The IP module merely specifies an IP host group destination, rather than an individual IP destination, when it invokes the existing "Send Local" operation.

Extensions to an Ethernet Local Network Module The Ethernet directly supports the sending of local multicast packets by allowing multicast addresses in the destination field of Ethernet packets. All that is needed to support the sending of multicast IP datagrams is a procedure for mapping IP host group addresses to Ethernet multicast addresses. An IP host group address is mapped to an Ethernet multicast address by placing the low-order 23-bits of the IP address into the low-order 23 bits of the Ethernet multicast address 01-00-5E-00-00-00 (hex). Because there are 28 significant bits in an IP host group address, more than one host group address may map to the same Ethernet multicast address. Mapping of IPv6 host group addresses to Ethernet is defined in and .

Extensions to Local Network Modules other than Ethernet Other networks that directly support multicasting, such as rings or buses conforming to the IEEE 802.2 standard, may be handled the same way as Ethernet for the purpose of sending multicast IP datagrams. For a network that supports broadcast but not multicast, such as the Experimental Ethernet, all IP host group addresses may be mapped to a single local broadcast address (at the cost of increased overhead on all local hosts). For a point-to-point link joining two hosts (or a host and a multicast router), multicasts SHOULD be transmitted exactly like unicasts. For a store-and-forward network like the ARPANET or a public X.25 network, all IP host group addresses might be mapped to the well-known local address of an IP multicast router; a router on such a network would take responsibility for completing multicast delivery within the network as well as among networks.

RECEIVING MULTICAST IP DATAGRAMS

Extensions to the IP Service Interface Incoming multicast IP datagrams are received by upper-layer protocol modules using the same "Receive IP" operation as normal, unicast datagrams. Selection of a destination upper-layer protocol is based on the protocol field in the IP header, regardless of the destination IP address. However, before any datagrams destined to a particular group can be received, an upper-layer protocol must ask the IP module to join that group. Thus, the IP service interface MUST be extended to provide two new operations:

The JoinHostGroup operation requests that this host become a member of the host group identified by "group-address" on the given network interface. The LeaveGroup operation requests that this host give up its membership in the host group identified by "group-address" on the given network interface. The interface argument may be omitted on hosts that support only one interface. For hosts that may be attached to more than one network, the upper-layer protocol may choose to leave the interface unspecified, in which case the request will apply to the default interface for sending multicast datagrams (see section 6.1). It is permissible to join the same group on more than one interface, in which case duplicate multicast datagrams may be received. It is also permissible for more than one upper-layer protocol to request membership in the same group. Both operations SHOULD return immediately (i.e., they are non- blocking operations), indicating success or failure. Either operation may fail due to an invalid group address or interface identifier. JoinHostGroup may fail due to lack of local resources. LeaveHostGroup may fail because the host does not belong to the given group on the given interface. LeaveHostGroup may succeed, but the membership persist, if more than one upper-layer protocol has requested membership in the same group. IPv6 socket extensions supporting these functions are defined in , section 5.2. specifies these functions for IP and IPv6 (as well as for SSM). Note that these are UDP socket extions (and not IP/IPv6 socket extensions due to the absence of widely available/used IP/IPv6 level socket APIs).

Extensions to the IP Module To support the reception of multicast IP datagrams, the IP module MUST be extended to maintain a list of host group memberships associated with each network interface. An incoming datagram destined to one of those groups is processed exactly the same way as datagrams destined to one of the host's individual addresses. Incoming datagrams destined to groups to which the host does not belong are discarded without generating any error report or log entry. On hosts with more than one network interface, if a datagram arrives via one interface, destined for a group to which the host belongs only on a different interface, the datagram is quietly discarded. (These cases should occur only as a result of inadequate multicast address filtering in a local network module.) An incoming datagram is not rejected for having an IP time-to-live of 1 (i.e., the time-to-live should not automatically be decremented on arriving datagrams that are not being forwarded). An incoming datagram with an IP host group address in its source address field is quietly discarded. An ICMP/ICMPv6 error message (Destination Unreachable, Time Exceeded, Parameter Problem, Source Quench, or Redirect) is never generated in response to a datagram destined to an IP host group. The list of host group memberships is updated in response to JoinHostGroup and LeaveHostGroup requests from upper-layer protocols. Each membership should have an associated reference count or similar mechanism to handle multiple requests to join and leave the same group. On the first request to join and the last request to leave a group on a given interface, the local network module for that interface is notified, so that it may update its multicast reception filter (see section 7.3). The IP module MUST also be extended to implement the IGMP protocol for IP and/or the MLD protocol for IPv6 (depending on the version of IP to be supported). IGMP/MLD are used to keep neighboring multicast routers informed of the host group memberships present on a particular local network.

Extensions to the Local Network Service Interface Incoming local network multicast packets are delivered to the IP module using the same "Receive Local" operation as local network unicast packets. To allow the IP module to tell the local network module which multicast packets to accept, the local network service interface is extended to provide two new operations:

where "group-address" is an IP host group address. The JoinLocalGroup operation requests the local network module to accept and deliver up subsequently arriving packets destined to the given IP host group address. The LeaveLocalGroup operation requests the local network module to stop delivering up packets destined to the given IP host group address. The local network module is expected to map the IP host group addresses to local network addresses as required to update its multicast reception filter. Any local network module is free to ignore LeaveLocalGroup requests, and may deliver up packets destined to more addresses than just those specified in JoinLocalGroup requests, if it is unable to filter incoming packets adequately. The local network module MUST NOT deliver up any multicast packets that were transmitted from that module; loopback of multicasts is handled at the IP layer or higher.

Extensions to an Ethernet Local Network Module To support the reception of multicast IP datagrams, an Ethernet module MUST be able to receive packets addressed to the Ethernet multicast addresses that correspond to the host's IP host group addresses. It is highly desirable to take advantage of any address filtering capabilities that the Ethernet hardware interface may have, so that the host receives only those packets that are destined to it. Unfortunately, many current Ethernet interfaces have a small limit on the number of addresses that the hardware can be configured to recognize. Nevertheless, an implementation MUST be capable of listening on an arbitrary number of Ethernet multicast addresses, which may mean "opening up" the address filter to accept all multicast packets during those periods when the number of addresses exceeds the limit of the filter. For interfaces with inadequate hardware address filtering, it may be desirable (for performance reasons) to perform Ethernet address filtering within the software of the Ethernet module. This is not mandatory, however, because the IP module performs its own filtering based on IP destination addresses.

Extensions to Local Network Modules other than Ethernet Other multicast networks, such as IEEE 802.2 networks, can be handled the same way as Ethernet for the purpose of receiving multicast IP datagrams. For pure broadcast networks, such as the Experimental Ethernet, all incoming broadcast packets can be accepted and passed to the IP module for IP-level filtering. On point-to-point or store-and-forward networks, multicast IP datagrams will arrive as local network unicasts, so no change to the local network module should be necessary.

Normative changes

Moving RFC1112 and IGMPv1 to historic status This document moves to historic status so that the IGMP version 1 protocol as specified in Appendix 1 of is moved to historic status. This protocol is not included in the text of this document anymore, which hence renders IGMPv1 historic. All other aspects of beside IGMPv1 are inherited and enhanced by this document and maintain their current Internet Standard designation from through the normative status of this document.

Backward compatibility with IGMPv1 Newer versions of IGMP or other protocols/mechisms including but not necessary limited to , or do or may (such as in ) include backward compatibility with IGMPv1, which requires the specification of IGMPv1. This document does not ask for any change to any specifications or implementations that includes any form of support for IGMPv1 for backward compatibility reasons as long as it also includes compatibility with a newer version of IGMP starting with . Any new or updated specification that wants to maintain such such backward compatibility with IGMPv1 needs to continue to reference the specification of IGMPv1 via . Any future reference for new or updated work to any other definition from needs to refer to this document instead.

Changes from RFC1112 Beyond the normative changes described in , this document introduces the following changes over .

Normative language This document introduces the use of normative language through capitalization. preceeded this method and hence did not include this language.

Superceeding references to IGMPv1 References to IGMPv1 in are replaced by references to in this text.

Introduction of the term Any-Source Multicast (ASM) This update introduces the term "ASM IP multicast" (ASM) as another term for "Host Extensions for IP multicast". This term was introduced when introduced another service model for IP Multicast called "Source Specific Multicast" (SSM), and hence, the service described in and this update is more precisely called Any Source Multicast (ASM) IP multicast. defines and uses the term "host group". This term is not applicable to IP/IPv6 multicast group addresses that are not used for ASM but SSM according to . New text in this document explains this. No functional changes to the IP Multicast service are incurred by these changes.

Applicability to both IP and IPv6 This document is written to apply to both IP and IPv6 by adding equivalent detail for IPv6 where only covered IP: addressing and protocols in support of the service - Multicast Listener Discovery for IPv6 versus IGMP for IP. Note: IPv6 documents such as and all its updates (e.g.: ) are defining multicasting in the assumption of the service of for IPv6, but without being able to refer to , as it was only defined for IP. Future documents can refer to this document as the IP Multicast / ASM service for both IP and IPv6. Additional text provides references for IETF UDP socket API specifications that instantiate the abstract APIs defined in this document. No functional changes to the IP Multicast service are incurred by these text changes.

Standard for IP multicasting in controlled networks This document removes the claim in the abstract of , that these host extensions are "... the recommended standard for IP multicasting in the Internet." The reason for this is that deprecated the ASM Service across the Internet because there is no Internet Standard solution for protocols to support interdomain ASM except for , which is only applicable to IPv6, and even that solution does not resolve the challenges to source access control in interdomain deployments. In result, ASM is today "only" a recommended solution for controlled networks including controlled federated networks for applications for which SSM is not usable. However, these limitations to the applicability of ASM to no impact the applicability of most of the host stack described in this document for other forms of IP Multicast, specifically "Source Specific Multicast", , which inherits all aspects of ASM specified in this document, especially the sending (, ) of IP Multicast packets as well as the mapping to ethernet (). It only amends the joining of IP Multicast traffic on IP Multicast receivers with additional procedures fitting into the host stack described in this document.

This memo specifies the extensions required of a host implementation of the Internet Protocol (IP) to support multicasting. Recommended procedure for IP multicasting in the Internet. This RFC obsoletes RFCs 998 and 1054. [STANDARDS-TRACK] This memo documents IGMPv2, used by IP hosts to report their multicast group memberships to routers. It updates STD 5, RFC 1112. [STANDARDS-TRACK] This document specifies the frame format for transmission of IPv6 packets and the method of forming IPv6 link-local addresses and statelessly autoconfigured addresses on Ethernet networks. It also specifies the content of the Source/Target Link-layer Address option used in Router Solicitation, Router Advertisement, Neighbor Solicitation, Neighbor Advertisement and Redirect messages when those messages are transmitted on an Ethernet. [STANDARDS-TRACK] This specification defines the addressing architecture of the IP Version 6 (IPv6) protocol. The document includes the IPv6 addressing model, text representations of IPv6 addresses, definition of IPv6 unicast addresses, anycast addresses, and multicast addresses, and an IPv6 node's required addresses. This document obsoletes RFC 3513, "IP Version 6 Addressing Architecture". [STANDARDS-TRACK] IP version 4 (IPv4) addresses in the 232/8 (232.0.0.0 to 232.255.255.255) range are designated as source-specific multicast (SSM) destination addresses and are reserved for use by source-specific applications and protocols. For IP version 6 (IPv6), the address prefix FF3x::/32 is reserved for source-specific multicast use. This document defines an extension to the Internet network service that applies to datagrams sent to SSM addresses and defines the host and router requirements to support this extension. [STANDARDS-TRACK] This document specifies version 6 of the Internet Protocol (IPv6). It obsoletes RFC 2460. In many standards track documents several words are used to signify the requirements in the specification. These words are often capitalized. This document defines these words as they should be interpreted in IETF documents. This document specifies an Internet Best Current Practices for the Internet Community, and requests discussion and suggestions for improvements. RFC 2119 specifies common key words that may be used in protocol specifications. This document aims to reduce the ambiguity by clarifying that only UPPERCASE usage of the key words have the defined special meanings. Google Switzerland GmbH University of Oslo Netflix University of Aberdeen Ericsson University of Glasgow SAP SE Apple Inc. This document describes an abstract application programming interface, API, to the transport layer that enables the selection of transport protocols and network paths dynamically at runtime. This API enables faster deployment of new protocols and protocol features without requiring changes to the applications. The specified API follows the Transport Services architecture by providing asynchronous, atomic transmission of messages. It is intended to replace the BSD sockets API as the common interface to the transport layer, in an environment where endpoints could select from multiple network paths and potential transport protocols. This memo specifies the Versatile Message Transaction Protocol (VMTP) [Version 0.7 of 19-Feb-88], a transport protocol specifically designed to support the transaction model of communication, as exemplified by remote procedure call (RPC). The full function of VMTP, including support for security, real-time, asynchronous message exchanges, streaming, multicast and idempotency, provides a rich selection to the VMTP user level. Subsettability allows the VMTP module for particular clients and servers to be specialized and simplified to the services actually required. Examples of such simple clients and servers include PROM network bootload programs, network boot servers, data sensors and simple controllers, to mention but a few examples. This RFC describes a protocol proposed as a standard for the Internet community. This document specifies version 6 of the Internet Protocol (IPv6), also sometimes referred to as IP Next Generation or IPng. [STANDARDS-TRACK] This memo specifies the frame format for transmission of IPv6 [IPV6] packets and the method of forming IPv6 link-local addresses on Ethernet networks. [STANDARDS-TRACK] The de facto standard Application Program Interface (API) for TCP/IP applications is the "sockets" interface. Although this API was developed for Unix in the early 1980s it has also been implemented on a wide variety of non-Unix systems. TCP/IP applications written using the sockets API have in the past enjoyed a high degree of portability and we would like the same portability with IPv6 applications. But changes are required to the sockets API to support IPv6 and this memo describes these changes. These include a new socket address structure to carry IPv6 addresses, new address conversion functions, and some new socket options. These extensions are designed to provide access to the basic IPv6 features required by TCP and UDP applications, including multicasting, while introducing a minimum of change into the system and providing complete compatibility for existing IPv4 applications. Additional extensions for advanced IPv6 features (raw sockets and access to the IPv6 extension headers) are defined in another document. This memo provides information for the Internet community. The Internet Group Management Protocol (IGMPv3) for IPv4 and the Multicast Listener Discovery (MLDv2) for IPv6 add the capability for applications to express source filters on multicast group memberships, which allows receiver applications to determine the set of senders (sources) from which to accept multicast traffic. This capability also simplifies support of one-to-many type multicast applications. This document specifies new socket options and functions to manage source filters for IP Multicast group memberships. It also defines the socket structures to provide input and output arguments to these new application program interfaces (APIs). These extensions are designed to provide access to the source filtering features, while introducing a minimum of change into the system and providing complete compatibility for existing multicast applications. This document updates RFC 2710, and it specifies Version 2 of the ulticast Listener Discovery Protocol (MLDv2). MLD is used by an IPv6 router to discover the presence of multicast listeners on directly attached links, and to discover which multicast addresses are of interest to those neighboring nodes. MLDv2 is designed to be interoperable with MLDv1. MLDv2 adds the ability for a node to report interest in listening to packets with a particular multicast address only from specific source addresses or from all sources except for specific source addresses. [STANDARDS-TRACK] This memo defines an address allocation policy in which the address of the Rendezvous Point (RP) is encoded in an IPv6 multicast group address. For Protocol Independent Multicast - Sparse Mode (PIM-SM), this can be seen as a specification of a group-to-RP mapping mechanism. This allows an easy deployment of scalable inter-domain multicast and simplifies the intra-domain multicast configuration as well. This memo updates the addressing format presented in RFC 3306. [STANDARDS-TRACK] This memo describes the recommendations for Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) snooping switches. These are based on best current practices for IGMPv2, with further considerations for IGMPv3- and MLDv2-snooping. Additional areas of relevance, such as link layer topology changes and Ethernet-specific encapsulation issues, are also considered. This memo provides information for the Internet community. This document specifies the Neighbor Discovery protocol for IP Version 6. IPv6 nodes on the same link use Neighbor Discovery to discover each other's presence, to determine each other's link-layer addresses, to find routers, and to maintain reachability information about the paths to active neighbors. [STANDARDS-TRACK] This document describes lightweight IGMPv3 and MLDv2 protocols (LW- IGMPv3 and LW-MLDv2), which simplify the standard (full) versions of IGMPv3 and MLDv2. The interoperability with the full versions and the previous versions of IGMP and MLD is also taken into account. [STANDARDS-TRACK] When transmitting an IPv6 packet with a multicast destination address, the IPv6 destination address is mapped to an Ethernet link-layer multicast address. This document clarifies that a mapping of an IPv6 packet with a multicast destination address may in some circumstances map to an Ethernet link-layer unicast address. [STANDARDS-TRACK] This document updates the definitions of IPv6 multicast scopes and therefore updates RFCs 4007 and 4291. This document updates the IPv6 multicast addressing architecture by redefining the reserved bits as generic flag bits. The document also provides some clarifications related to the use of these flag bits. This document updates RFCs 3956, 3306, and 4291. This document recommends deprecation of the use of Any-Source Multicast (ASM) for interdomain multicast. It recommends the use of Source-Specific Multicast (SSM) for interdomain multicast applications and recommends that hosts and routers in these deployments fully support SSM. The recommendations in this document do not preclude the continued use of ASM within a single organization or domain and are especially easy to adopt in existing deployments of intradomain ASM using PIM Sparse Mode (PIM-SM).

HOST GROUP ADDRESS ISSUES This appendix is not part of the IP multicasting specification, but provides background discussion of several issues related to IP host group addresses.

Group Address Binding The binding of IP host group addresses to physical hosts may be considered a generalization of the binding of IP unicast addresses. An IP unicast address is statically bound to a single local network interface on a single IP network. An IP host group address is dynamically bound to a set of local network interfaces on a set of IP networks. It is important to understand that an IP host group address is NOT bound to a set of IP unicast addresses. The multicast routers do not need to maintain a list of individual members of each host group. For example, a multicast router attached to an Ethernet need associate only a single Ethernet multicast address with each host group having local members, rather than a list of the members' individual IP or Ethernet addresses.

Allocation of Transient Host Group Addresses This memo does not specify how transient group address are allocated. It is anticipated that different portions of the IP transient host group address space will be allocated using different techniques. For example, there may be a number of servers that can be contacted to acquire a new transient group address. Some higher-level protocols (such as VMTP, specified in ) may generate higher- level transient "process group" or "entity group" addresses which are then algorithmically mapped to a subset of the IP transient host group addresses, similarly to the way that IP host group addresses are mapped to Ethernet multicast addresses. A portion of the IP group address space may be set aside for random allocation by applications that can tolerate occasional collisions with other multicast users, perhaps generating new addresses until a suitably "quiet" one is found. In general, a host cannot assume that datagrams sent to any host group address will reach only the intended hosts, or that datagrams received as a member of a transient host group are intended for the recipient. Misdelivery must be detected at a level above IP, using higher-level identifiers or authentication tokens. Information transmitted to a host group address should be encrypted or governed by administrative routing controls if the sender is concerned about unwanted listeners.

Discussion and Explanations (TO BE REMOVED) [RFC-editor: Please remove this section] Please refer to for the non-process disucssion of the goals of this document.

Goals of this document The goal of this document is to allow for IETF to declare historic and inherit the full INTERNET STANDARD status of with this document immediately - without going through the otherwise necessary long process. The reason why needs to be declared historic is so that the IGMP version 1 protocol specified in it can be declared obsolete. This update removes IGMPv1 text. The reason why this document is still needed (as an Internet Standard), is because the IP Multicast service specified in has since its inception been the Internet Standard for the IP Multicasting service. To allow for this document to gets immediately the intended Internet Standard status, it introduces no functional changes and it deliverately avoids also any unnecessary textual changes. This includes the deliberade non-upgrade of the language to use terminology. While the use of that language might be preferred for new work/text, the success of IP Multicasting as defined in seems to indicate that the existing text was more than sufficient.

Internet Standard status Note that the removal of the IGMPv1 protocol may raise the question whether the document in its current form still contains specifications sufficient for Internet Standard as opposed to Informational. The core aspects that impacts interoperability (and hence qualifies the document for Internet Standard) is the format of IP packets when IP Multicast service is used, e.g.: IP Multicast addressing and binding to Multicast Ethernet MAC addresses. There is no other RFC that introduces these specifications for IP, because there was never another update to to do this. , another standards track document bilding on , defining the SSM service / host stack. This update also includes the necessary text for IPv6. Note that for IPv6 the ethernet MAC address mapping of IPv6 multicast packets was later (after ) specified in and its updates, but scattering the aspects of IPv6 multicast across (currently) , {RFC4291}} and makes it arguably more difficult for implementers to understand the technology than this document that coalesces all these services aspects - from ethernet bonding to application interfac. Beyond those packet format/ethernet aspects, historically, the Multicast service (API) related text in would not have been considered to be an Internet Standards scope definition because this classification was not extended to (abstract) APIs, even though they do of course define an interoperability interface between e.g.: operating system providing the API and applications using it. Recently, the IETF has changed its stance on this issue though and is working on with the intent for it to become Internet Standard. With this in mind, all that text of can also be considered appropriate for Internet Standard.

Changelog This document is hosted at https://github.com/toerless/rfc1112bis. Please submit issues with this text as issues to that github and report them on pim@ietf.org.

Candidate Open Issues The following questions are left as candidate open issues, which so far the authors think do not deservice to be pursued, but the authors want to bring them to the awareness of reviewers. RFC1112 did not claim to be an update to rfc791 even though it does effectively update RFC791 because it exempts IP Multicast packets from RFC791 processing. And also introduces invalid packets (source address IP Multicast which are neither unicast nor multicast). If we would want, we can still declare this document to also be an update to rfc791. Likewise the same could apply to RFC8200 which does not specify these details either. This document could refer to the IGMPv3bis and MLDv2bis instead of current IGMPv3/MLDv2 RFCs.

draft-ietf-pim-rfc1112bis-02 Removed unused references, fefresh - waiting for more reviews.

draft-ietf-pim-rfc1112bis-01 Fix up reference for IGMPv3. Refined candidate open issues. Removed author discussion.

draft-ietf-pim-rfc1112bis-00 Just changed title, added github pointer.

draft-eckert-pim-rfc1112bis-02 Changed core references from numbered style to name style . Changed copyright clause to pre5378Trust200902, which is the same as used for RFC8200 due to the presence of text with similar early status. To resolve Dinos concerns at IETF116 with -01: Added hopefully extensive explanation wrt. to how to treat IGMPv1 based on Dino's feedback from IETF117: This document does not ask for any removal of IGMPv1 in any IETF specs which include it for backward compatibility reasons, it only effectively causes it to become historic once RFC1112 would be declared historic. To resolve Alvaros concerns at IETF1116 with -01: Added normative language (MUST/SHOULD). Seems as if this is quite easy given how "must" was written appropriately in the original text. The logic of applying MUST/MUST-NOT was based on understanding by the author how none of the MUST would actually put existing working implementations out of compliance. Added explicit text to move rfc1112 to historic status. Moved explanation of changes from rfc1112 from appendix to main text as this seem to the common practice for document updates. Added claim for this document to be an update to rfc791. See open issues section though.

draft-eckert-pim-rfc1112bis-01 Changed all use of IPv4 back to IP. Seems standard in IETF specs. Only IPv6 has in IETF specs the distinction of including the version. Changed Steve Deerings address to a pseudo-email address at IETF. See prior section. Converted document into kramdownrfc2629 format for easier editing. Claims that rfc2119 language is not desired/used (to maintain maximum original text without changes). Rewrote section for updates to rfc1112 to hopefully better motivate/explain the reason for this document and detail what its changes are.

draft-eckert-pim-rfc1112bis-00 Initial version based on text version, edited.