]> Deutsches Forschungsnetz | German National Research and Education Network

Alexanderplatz 1 Berlin 10178 Germany rieckers@dfn.de www.dfn.de

Fondation Restena | Restena Foundation

2, avenue de l'Université Esch-sur-Alzette 4365 Luxembourg stefan.winter@restena.lu www.restena.lu

Security RADIUS EXTensions RADIUS TLS This document specifies a transport profile for RADIUS using Transport Layer Security (TLS) over TCP or Datagram Transport Layer Security (DTLS) over UDP as the transport protocol. This enables encrypting the RADIUS traffic as well as dynamic trust relationships between RADIUS servers. The specification obsoletes the experimental specifications in RFC 6614 (RADIUS/TLS) and RFC 7360 (RADIUS/DTLS) and combines them in this specification. About This Document Status information for this document may be found at . Discussion of this document takes place on the RADIUS EXTensions Working Group mailing list (), which is archived at . Subscribe at .

Introduction The RADIUS protocol is a widely deployed authentication, authorization and accounting solution. It is defined in , , and others. The deployment experience has shown several shortcomings, such as its dependency on the unreliable transport protocol UDP and the lack of confidentiality for large parts of its packet payload. Additionally the confidentiality and integrity mechanisms rely on the MD5 algorithm, which has been proven to be insecure. Although RADIUS/(D)TLS does not remove the MD5-based mechanisms, it adds confidentiality and integrity protection through the TLS layer. For an updated version of RADIUS/(D)TLS without need for MD5 see

Purpose of RADIUS/(D)TLS The main focus of RADIUS/TLS and RADIUS/DTLS is to provide means to secure communication between RADIUS peers using TLS or DTLS. The most important use of this specification lies in roaming environments where RADIUS packets need to be sent across insecure or untrusted networks. An example for a worldwide roaming environment that uses RADIUS over TLS to secure communication is eduroam as described in

Changes from RFC6614 (RADIUS/TLS) and RFC7360 (RADIUS/DTLS)

• referenced for TCP-related specification, RFC6613 on the other hand had some specification for RADIUS/TLS. These specifications have been merged into this document.
• RFC6614 marked TLSv1.1 or later as mandatory, this specification requires TLSv1.2 as minimum and recommends usage of TLSv1.3.
• RFC6614 allowed usage of TLS compression, this document forbids it.
• RFC6614 only requires support for the trust model "certificates with PKIX" (). This document changes this. For servers, TLS-X.509-PKIX (, equivalent to "certificates with PKIX" in RFC6614) and TLS-PSK () is now mandated and clients must implement at least one of the two.
• The mandatory-to-implement cipher suites are not referenced directly, this is replaced by a pointer to the TLS BCP.
• The specification regarding steps for certificate verification has been updated.
• mandated the use of Status-Server as watchdog algorithm, only recommended it. This specification mandates the use of Status-Server for both RADIUS/TLS and RADIUS/DTLS.
• only included limited text around retransmissions, this document now gives more guidance on how to handle retransmissions, especially across different transports.
• The rules for verifying the peer certificate have been updated to follow guidance provided in . Using the Common Name RDN for validation is now forbidden.

The rationales behind some of these changes are outlined in .

Conventions and Definitions The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 when, and only when, they appear in all capitals, as shown here. Within this document we will use the following terms:

RADIUS/(D)TLS node:

a RADIUS-over-(D)TLS client or server

RADIUS/(D)TLS client:

a RADIUS-over-(D)TLS instance that initiates a new connection

RADIUS/(D)TLS server:

a RADIUS-over-(D)TLS instance that listens on a RADIUS-over-(D)TLS port and accepts new connections

RADIUS/UDP:

a classic RADIUS transport over UDP as defined in

Whenever "(D)TLS" or "RADIUS/(D)TLS" is mentioned, the specification applies for both RADIUS/TLS and RADIUS/DTLS. Where "TLS" or "RADIUS/TLS" is mentioned, the specification only applies to RADIUS/TLS, where "DTLS" or "RADIUS/DTLS" is mentioned it only applies to RADIUS/DTLS. Server implementations MUST support both RADIUS/TLS and RADIUS/DTLS. Client implementations SHOULD implement both, but MUST implement at least one of RADIUS/TLS or RADIUS/DTLS.

Changes to RADIUS This section discusses the needed changes to the RADIUS packet format (), port usage and shared secrets ().

Packet format The RADIUS packet format is unchanged from , and . Specifically, all of the following portions of RADIUS MUST be unchanged when using RADIUS/(D)TLS:

• Packet format
• Permitted codes
• Request Authenticator calculation
• Response Authenticator calculation
• Minimum packet length
• Maximum packet length
• Attribute format
• Vendor-Specific Attribute (VSA) format
• Permitted data types
• Calculation of dynamic attributes such as CHAP-Challenge, or Message-Authenticator
• Calculation of "encrypted" attributes such as Tunnel-Password.

The use of (D)TLS transport does not change the calculation of security-related fields (such as the Response-Authenticator) in RADIUS or RADIUS Dynamic Authorization . Calculation of attributes such as User-Password or Message-Authenticator also does not change. The changes to RADIUS implementations required to implement this specification are largely limited to the portions that send and receive packets on the network and the establishment of the (D)TLS connection. The requirement that RADIUS remain largely unchanged ensures the simplest possible implementation and widest interoperability of the specification. This includes the usage of the outdated security mechanisms in RADIUS that are based on shared secrets and MD5. This is not considered a security issue, since integrity and confidentiality are provided by the (D)TLS layer. See of this document or for more details. We note that for RADIUS/DTLS the DTLS encapsulation of RADIUS means that RADIUS packets have an additional overhead due to DTLS. This is discussed further in .

Default ports and shared secrets IANA has reserved ports for RADIUS/TLS and RADIUS/DTLS. Since authentication of peers, confidentiality, and integrity protection is achieved on the (D)TLS layer, the shared secret for the RADIUS packets is set to a static string, depending on the method. The calculation of security-related fields such as Response-Authenticator, Message-Authenticator or encrypted attributes MUST be performed using this shared secret.

Protocol	Port	Shared Secret
RADIUS/TLS	2083/tcp	"radsec"
RADIUS/DTLS	2083/udp	"radius/dtls"

RADIUS/(D)TLS does not use separate ports for authentication, accounting and dynamic authorization changes. The source port is arbitrary. For considerations regarding the multi-purpose use of one port for authentication and accounting see . RADIUS/TLS servers MUST immediately start the TLS negotiation when a new connection to the RADIUS/TLS port is opened. They MUST close the connection and discard any data sent if the connecting client does not start a TLS negotiation or if the TLS negotiation fails at any point. RADIUS/DTLS servers MUST silently discard any packet they receive over the RADIUS/DTLS port that is not a new DTLS negotiation or a packet sent over a DTLS session established earlier. RADIUS/(D)TLS peers MUST NOT use the old RADIUS/UDP or RADIUS/TCP ports for RADIUS/DTLS or RADIUS/TLS.

Detecting Live Servers As RADIUS is a "hop-by-hop" protocol, a RADIUS proxy shields the client from any information about downstream servers. While the client may be able to deduce the operational state of the local server (i.e., proxy), it cannot make any determination about the operational state of the downstream servers. Within RADIUS, proxies typically only forward traffic between the NAS and RADIUS servers, and they do not generate their own response. As a result, when a NAS does not receive a response to a request, this could be the result of packet loss between the NAS and proxy, a problem on the proxy, loss between the RADIUS proxy and server, or a problem with the server. The absence of a reply can cause a client to deduce (incorrectly) that the proxy is unavailable. The client could then fail over to another server or conclude that no "live" servers are available (OKAY state in , Appendix A). This situation is made even worse when requests are sent through a proxy to multiple destinations. Failures in one destination may result in service outages for other destinations, if the client erroneously believes that the proxy is unresponsive. RADIUS/(D)TLS implementations MUST utilize the existence of a TCP/DTLS connection along with the application-layer watchdog defined in to determine the liveliness of the server. RADIUS/(D)TLS clients MUST mark a connection DOWN if one or more of the following conditions are met:

• The administrator has marked the connection administrative DOWN.
• The network stack indicates that the connection is no longer viable.
• The application-layer watchdog algorithm has marked it DOWN.

If a RADIUS/(D)TLS client has multiple connection to a server, it MUST NOT decide to mark the whole server as DOWN until all connections to it have been marked DOWN.TODO: Explain what a server is. (Just the destination IP? include port?) RADIUS/(D)TLS clients MUST implement the Status-Server extension as described in as the application level watchdog to detect the liveliness of the peer in the absence of responses. Since RADIUS has a limitation of 256 simultaneous "in flight" packets due to the length of the ID field (, Section 2.4), it is RECOMMENDED that RADIUS/(D)TLS clients reserve ID zero (0) on each session for Status-Server packets. This value was picked arbitrary, as there is no reason to choose any other value over another for this use. For RADIUS/TLS, the peers MAY send TCP keepalives as described in . For RADIUS/DTLS connections, the peers MAY send periodic keepalives as defined in . This is a way of proactively and rapidly triggering a connection DOWN notification from the network stack. These liveliness checks are essentially redundant in the presence of an application-layer watchdog, but may provide more rapid notifications of connectivity issues.

Packet / Connection Handling This section defines the behaviour for RADIUS/(D)TLS peers for handling of incoming packets and establishment of a (D)TLS session.

(D)TLS requirements As defined in , RADIUS/(D)TLS clients MUST establish a (D)TLS session immediately upon connecting to a new server. RADIUS/(D)TLS has no notion of negotiating (D)TLS in an ongoing communication. As RADIUS has no provisions for capability signaling, there is also no way for a server to indicate to a client that it should transition to using TLS or DTLS. Servers and clients need to be preconfigured to use RADIUS/(D)TLS for a given endpoint. This action has to be taken by the administrators of the two systems. Implementations MUST follow the recommendations given in .TODO: Add text which recommendations of RFC9325 must be followed and why Additionally, the following requirements have to be met for the (D)TLS session:

• Support for TLS 1.2 / DTLS 1.2 is REQUIRED, support for TLS 1.3 / DTLS 1.3 or higher is RECOMMENDED.
• Negotiation of a cipher suite providing for confidentiality as well as integrity protection is REQUIRED.
• The peers MUST NOT negotiate compression.
• The session MUST be mutually authenticated (see )

Mutual authentication RADIUS/(D)TLS servers MUST authenticate clients, and RADIUS/(D)TLS clients MUST authenticate the server. RADIUS is designed to be used by mutually trusted systems. Allowing anonymous clients would ensure privacy for RADIUS/(D)TLS traffic, but would negate all other security aspects of the protocol, including security aspects of RADIUS itself, due to the fixed shared secret. RADIUS/(D)TLS allows for the following different modes of mutual authentication, which will be further specified in this section: * TLS-X.509-PKIX * TLS-X.509-FINGERPRINT * TLS-RAW-PUBLIC-KEY * TLS-PSK

Authentication using X.509 certificates with PKIX trust model (TLS-X.509-PKIX) All RADIUS/(D)TLS server implementations MUST implement this model. RADIUS/(D)TLS client implementations SHOULD implement this model, but MUST implement either this or TLS-PSK If implemented it MUST use the following rules:

• Implementations MUST allow the configuration of a trust anchor (i.e. a list of trusted Certificate Authorities (CAs)) for new TLS sessions. This list SHOULD be application specific and not use a global system trust store.
• Certificate validation MUST include the verification rules as per .
• Implementations SHOULD indicate their trust anchors when opening or accepting TLS sessions. See , Section 7.4.4 and , Section 6 for TLS 1.2 and , Section 4.2.4 for TLS 1.3.
• When the configured trust base changes (e.g., removal of a CA from the trust anchor; issuance of a new CRL for a given CA), implementations SHOULD reassess all connected peer's continued validity of the certificate path. Note that TLS 1.3 no longer supports renegotiation to fulfill this requirement. Open discussion: RFC6614 says "may" here. I think this should be a "should". There are some discussions to change this to "must". Input from TLS/UTA experts is appreciated.

RADIUS/(D)TLS clients and server MUST follow when validating peer identities. Specific details are provided below:

• The Common Name RDN MUST NOT be used to identify peers
• Certificates MAY use wildcards in the identifiers of DNS names and realm names, but only as the complete, left-most label.
• RADIUS/(D)TLS clients validate the servers identity to match their local configuration, accepting the identity on the first match:
  • If the expected RADIUS/(D)TLS server is associated with a specific NAI realm, e.g. by dynamic discovery or static configuration, that realm is matched against the presented identifiers of any subjectAltName entry of type otherName whose name form is NAIRealm as defined in .
  • If the expected RADIUS/(D)TLS server was configured as a hostname, or the hostname was yielded by a dynamic discovery procedure, that name is matched against the presented identifiers of any subjectAltName entry of type dNSName . Since a dynamic discovery might by itself not be secured, implementations MAY require the use of DNSSEC to ensure the authenticity of the DNS result before considering this identity as valid.
  • If the expected RADIUS/(D)TLS server was configured as an IP address, the configured IP address is matched against the presented identifier in any subjectAltName entry of type iPAddress .
  • Clients MAY use other attributes of the certificate to validate the servers identity, but it MUST NOT accept any certificate without validation.
  • Clients which also act as servers (i.e. proxies) may be susceptible to security issues when a ClientHello is mirrored back to themselves. More details on this issue are discussed in .
• RADIUS/(D)TLS servers validate the certificate of the RADIUS/(D)TLS client against a local database of acceptable clients. The database may enumerate acceptable clients either by IP address or by a name component in the certificate.
  • For clients configured by DNS name, the configured name is matched against the presented identifiers of any subjectAltName entry of type dNSName .
  • For clients configured by their source IP address, the configured IP address is matched against the presented identifiers of any subjectAltName entry of type iPAddress . For clients configured by IP range, the certificate MUST be valid for the IP address the client is currently using.
  • Implementation MAY consider additional subjectAltName extensions to identify a client.
  • If configured by the administrator, the identity check MAY be omitted after a successful trust chain check, e.g. if the client used dynamic lookup there is no configured client identity to verify. The clients authorization MUST then be validated using a certificate policy OID unless both peers are part of a trusted network.
• Implementations MAY allow configuration of a set of additional properties of the certificate to check for a peer's authorization to communicate (e.g. a set of allowed values presented in subjectAltName entries of type uniformResourceIdentifier or a set of allowed X.509v3 Certificate Policies).

Authentication using X.509 certificate fingerprints (TLS-X.509-FINGERPRINT) RADIUS/(D)TLS implementations SHOULD allow the configuration of a list of trusted certificates, identified via fingerprint of the DER encoded certificate bytes. When implementing this model, support for SHA-1 as hash algorithm for the fingerprint is REQUIRED, and support for the more contemporary hash function SHA-256 is RECOMMENDED.

Authentication using Raw Public Keys (TLS-RAW-PUBLIC-KEYS) RADIUS/(D)TLS implementations SHOULD support using Raw Public Keys for mutual authentication.

Authentication using TLS-PSK (TLS-PSK) RADIUS/(D)TLS server implementations MUST support the use of TLS-PSK. RADIUS/(D)TLS client implementations SHOULD support the use of TLS-PSK, but MUST implement either this or the TLS-X.509-PKIX trust model. Further guidance on the usage of TLS-PSK in RADIUS/(D)TLS is given in .

Connecting Client Identity In RADIUS/UDP, clients are uniquely identified by their IP addresses. Since the shared secret is associated with the origin IP address, if more than one RADIUS client is associated with the same IP address, then those clients also must utilize the same shared secret, a practice that is inherently insecure, as noted in . Depending on the trust model used, the RADIUS/(D)TLS client identity can be determined differently. With TLS-PSK, a client is uniquely identified by its TLS-PSK identifier. With TLS-RAW-PUBLIC-KEY, a client is uniquely identified by the Raw public key. With TLS-X.509-FINGERPRINT, a client is uniquely identified by the fingerprint of the presented client certificate. With TLS-X.509-PKIX, a client is uniquely identified by the tuple of the serial number of the presented client certificate and the issuer. Note well: having identified a connecting entity does not mean the server necessarily wants to communicate with that client. For example, if the Issuer is not in a trusted set of Issuers, the server may decline to perform RADIUS transactions with this client. Additionally, a server MAY restrict individual or groups of clients to certain IP ranges. A client connecting from outside this range would be rejected, even if the mutual authentication otherwise would have been successful. To reduce server load and to prevent probing the validity of stolen credentials, the server SHOULD abort the (D)TLS negotiation immediately with a TLS alert access_denied(49) after the client transmitted identifying information, i.e. the client certificate or the PSK identifier, and the server recognizes that the client connects from outside the allowed IP range. There are numerous trust models in PKIX environments, and it is beyond the scope of this document to define how a particular deployment determines whether a client is trustworthy. Implementations that want to support a wide variety of trust models should expose as many details of the presented certificate to the administrator as possible so that the trust model can be implemented by the administrator. As a suggestion, at least the following parameters of the X.509 client certificate should be exposed:

• Originating IP address
• Certificate Fingerprint
• Issuer
• Subject
• all X.509v3 Extended Key Usage
• all X.509v3 Subject Alternative Name
• all X.509v3 Certificate Policy

In TLS-PSK operation at least the following parameters of the TLS connection should be exposed:

• Originating IP address
• TLS-PSK Identifier

RADIUS Datagrams RADIUS/(D)TLS clients transmit the same packet types on the connection they initiated as a RADIUS/UDP client would, RADIUS/(D)TLS servers transmit the same packet types on the connections they have accepted as a RADIUS/UDP server would. Due to the use of one single port for all packet types, it is required that a RADIUS/(D)TLS server signals which types of packets are supported on a server to a connecting peer.

• When an unwanted packet of type 'CoA-Request' or 'Disconnect-Request' is received, a RADIUS/(D)TLS server needs to respond with a 'CoA-NAK' or 'Disconnect-AK', respectively. The NAK SHOULD contain an attribute Error-Cause with the value 406 ("Unsupported Extension"); see for details.
• When an unwanted packet of type 'Accounting-Request' is received, the RADIUS/(D)TLS server SHOULD reply with an Accounting-Response containing an Error-Cause attribute with value 406 "Unsupported Extensions" as defined in . A RADIUS/(D)TLS accounting client receiving such an Accounting-Response SHOULD log the error and stop sending Accounting-Request packets.TODO: Comment from Alan to send a Protocol Error packet instead.

Forwarding RADIUS packets between UDP and TCP based transports When proxy forwards packets, it is possible that the incoming and outgoing links have substantially different properties. This issue is most notable in UDP to TCP proxying, but there are still possible issues even when the same transport is used on both incoming and outgoing links. noted this issue many years ago: These differences are most notable in throughput, and in differing retransmission requirements.

Throughput Differences lead to Network Collapse An incoming link to the proxy may have substantially lower throughput than the outgoing link. Perhaps the network characteristics on the two links are different, or perhaps the home server is slow. In both situations, the proxy is left with a difficult choice about what to do with the incoming packets. As RADIUS does not provide for connection-based congestion control, there is no way for the proxy to signal on the incoming link that the client should slow its rate of sending packets. As a result, the proxy must simply accept the packets, buffer them, and hope that they can be be sent outbound before the client gives up on the request. The situation is made worse by the sub-optimal behavior of Accounting-Request packets. defines the Acct-Delay-Time attribute, which is supposed to be updated on retransmissions. However, when the value of the attribute is updated, changing the Acct-Delay-Time causes the Identifier to change. The "retransmitted" packet is therefore not, in fact, retransmitted, but is instead a brand new packet. This behavior increases the number of packets handled by proxies, which leads to congestive collapse. This design also violates the "end-to-end" principles discussed in which discusses congestion avoidance: In order to avoid congestive collapse, is is RECOMMENDED that RADIUS/TLS clients which originate Accounting-Request packets (i.e. not proxies) do not include Acct-Delay-Time in those packets. Instead, those clients SHOULD include Event-Timestamp, which is the time at which the original event occurred. The Event-Timestamp MUST NOT be updated on any retransmissions, as that would both negate the meaning of Event-Timestamp, and also create the same problem as with Acct-Delay-Time. This change is imperfect, but will at least help to avoid congestive collapse.

Differing Retransmission Requirements Due to the lossy nature of UDP, RADIUS/UDP and RADIUS/DTLS transports are required to perform retransmissions as per . In contrast, RADIUS/TCP and RADIUS/TLS transports are reliable, and do not perform retransmissions. These requirements lead to an issue for proxies when they send packets across protocol boundaries with differing retransmission behaviors. When a proxy receives packets on an unreliable transport, and forwards them across a reliable transport, it receives retransmissions from the client, but MUST NOT forward those retransmissions across the reliable transport. The proxy MAY log information about these retransmissions, but it does not perform any other action. When a proxy receives packets on a reliable transport, and forwards them across an unreliable transport, the proxy MUST perform retransmissions across the unreliable transport as per . That is, the proxy takes responsibility for the retransmissions. Implementations MUST take care to not completely decouple the two transports in this situation. That is, if an incoming connection on a reliable transport is closed, there may be pending retransmissions on an outgoing unreliable transport. Those retransmissions MUST be stopped, as there is nowhere to send the reply. Similarly, if the proxy sees that the client has given up on a request (such as by re-using an Identifier before the proxy has sent a response), the proxy MUST stop all retransmissions, and discard the old request. The above requirements are a logical extension of the common practice where a client stops retransmission of a packet once it decides to "give up" on the packet and discard it. Whether this discard process is due to internal client decisions, or interaction with incoming connections is irrelevant. When the client cannot do anything with responses to a request, it MUST stop retransmitting that request. In an ideal world, a proxy could also apply the suggestion of the previous section, by discarding Acct-Delay-Time from Accounting-Request packets, and replacing it with Event-Timestamp. However, this process is fragile and is not known to succeed in the general case.

Session limits and timeout While RADIUS/UDP could be implemented mostly stateless (except for the requests in flight), both TCP/TLS as well as DTLS require state tracking of the underlying TLS connection and are thus subject to potential resource exhaustion. This is aggravated by the fact that radius client/servers are often statically configured and thus form long-running peer relationships with long-running connections. Implementations SHOULD have configurable limits on the number of open connections. When this maximum is reached and a new session is started, the server MUST either drop an old session in order to open the new one or not create a new session. The close notification of (D)TLS or underlying connections are not fully reliable, or they might be unnecessarily kept alive by heartbeat or watchdog traffic, occupying resources. Therefore, both RADIUS/(D)TLS clients and servers MAY close connections after they have been idle for some time (no traffic except application layer watchdog). This idle timeout SHOULD be configurable within reasonable limits and SHOULD allow to disable idle timeout completely. On the server side, this mostly helps avoid resource exhaustion. For clients, proactively closing sessions can also help mitigate situations where watchdog mechanisms are unavailable or fail to detect non-functional connections. Some scenarios or RADIUS protocol extensions could also require that a connection be kept open at all times, so clients MAY immediately re-open the connection. These scenarios could be related to monitoring the infrastructure or to allow the server to proactively send packets to the clients without a preceding request. The value of the idle timeout to use depends on the exact deployment and is a trade-of between resource usage on clients/servers and the overhead of opening new connections. Very short timeouts that are at or below the timeouts used for application layer watchdogs, typically in the range of 30-60s can be considered unreasonable. In contrast, the upper limit is much more difficult to define but may be in the range of 10 to 15min, depending on the available resources, or never (disabling idle timeout) in scenarios where a permanently open connection is required.

RADIUS/TLS specific specifications This section discusses all specifications that are only relevant for RADIUS/TLS.

Duplicates and Retransmissions As TCP is a reliable transport, RADIUS/TLS peers MUST NOT retransmit RADIUS packets over a given TCP connection. Similarly, if there is no response to a RADIUS packet over one RADIUS/TLS connection, implementations MUST NOT retransmit that packet over a different connection to the same destination IP address and port, while the first connection is in the OKAY state (. TODO: Destination IP addr and port may be bad, but what is a server's identity? However, if the TLS session or TCP connection is closed or broken, retransmissions over new connections are permissible. RADIUS request packets that have not yet received a response MAY be transmitted by a RADIUS/TLS client over a new connection. As this procedure involves using a new source port, the ID of the packet MAY change. If the ID changes, any security attributes such as Message-Authenticator MUST be recalculated. If a TLS session or the underlying TCP connection is closed or broken, any cached RADIUS response packets () associated with that connection MUST be discarded. A RADIUS server SHOULD stop the processing of any requests associated with that TLS session. No response to these requests can be sent over the TLS connection, so any further processing is pointless. This requirement applies not only to RADIUS servers, but also to proxies. When a client's connection to a proxy is closed, there may be responses from a home server that were supposed to be sent by the proxy back over that connection to the client. Since the client connection is closed, those responses from the home server to the proxy server SHOULD be silently discarded by the proxy. Despite the above discussion, RADIUS servers SHOULD still perform duplicate detection on received packets, as described in . This detection can prevent duplicate processing of packets from non-conforming clients. RADIUS packets SHOULD NOT be retransmitted to the same destination IP and numerical port, but over a different transport protocol. There is no guarantee in RADIUS that the two ports are in any way related. This requirement does not, however, forbid the practice of putting multiple servers into a failover or load-balancing pool. In that situation, RADIUS requests MAY be retransmitted to another server that is known to be part of the same pool.

Malformed Packets and Unknown clients The RADIUS specifications say that an implementation should "silently discard" a packet in a number of circumstances. This action has no further consequences for UDP based transports, as the "next" packet is completely independent of the previous one. When TLS is used as transport, decoding the "next" packet on a connection depends on the proper decoding of the previous packet. As a result the behavior with respect to discarded packets has to change. Implementations of this specification SHOULD tread the "silently discard" texts in the RADIUS specification referenced above as "silently discard and close the connection". That is, the implementation SHOULD send a TLS close notification and the underlying TCP connection MUST be closed if any of the following circumstances are seen:

• Connection from an unknown client
• Packet where the RADIUS "Length" field is less than the minimum RADIUS packet length
• Packet where the RADIUS "Length" field is more than the maximum RADIUS packet length
• Packet where an Attribute "Length" field has the value of zero or one (0 or 1)
• Packet where the attributes do not exactly fill the packet
• Packet where the Request Authenticator fails validation (where validation is required)
• Packet where the Response Authenticator fails validation (where validation is required)
• Packet where the Message-Authenticator attribute fails validation (when it occurs in a packet)

After applying the above rules, there are still two situations where the previous specifications allow a packet to be "silently discarded" upon receipt:

• Packet with an invalid code field
• Response packets that do not match any outstanding request

In these situations, the TCP connections MAY remain open, or they MAY be closed, as an implementation choice. However, the invalid packet MUST be silently discarded. These requirements reduce the possibility for a misbehaving client or server to wreak havoc on the network.

TCP Applications Are Not UDP Applications Implementors should be aware that programming a robust TCP-based application can be very different from programming a robust UDP-based application. Additionally, differences in the transport like Head of Line (HoL) blocking should be considered. When using RADIUS/UDP or RADIUS/DTLS, there is no ordering of packets. If a packet sent by a peer is lost, that loss has no effect on subsequent packets sent by that peer. Unlike UDP, TCP is subject to issues related to Head of Line blocking. This occurs when a TCP segment is lost and a subsequent TCP segment arrives out of order. While the RADIUS peers can process RADIUS packets out of order, the semantics of TCP makes this impossible. This limitation can lower the maximum packet processing rate of RADIUS/TLS.

RADIUS/DTLS specific specifications This section discusses all specifications that are only relevant for RADIUS/DTLS.

RADIUS packet lengths The DTLS encryption adds an additional overhead to each packet sent. RADIUS/DTLS implementations MUST support sending and receiving RADIUS packets of 4096 bytes in length, with a corresponding increase in the maximum size of the encapsulated DTLS packets. This larger packet size may cause the packet to be larger than the Path MTU (PMTU), where a RADIUS/UDP packet may be smaller. The Length checks defined in MUST use the length of the decrypted DTLS data instead of the UDP packet length. They MUST treat any decrypted DTLS data bytes outside the range of the length field as padding and ignore it on reception.

Server behavior When a RADIUS/DTLS server receives packets on the configured RADIUS/DTLS port, all packets MUST be treated as being DTLS. RADIUS/UDP packets MUST NOT be accepted on this port. Some servers maintain a list of allowed clients per destination port. Others maintain a global list of clients that are permitted to send packets to any port. Where a client can send packets to multiple ports, the server MUST maintain a "DTLS Required" flag per client. This flag indicates whether or not the client is required to use DTLS. When set, the flag indicates that the only traffic accepted from the client is over the RADIUS/DTLS port. When packets are received from a client with the "DTLS Required" flag set on non-DTLS ports, the server MUST silently discard these packets, as there is no RADIUS/UDP shared secret available. This flag will often be set by an administrator. However, if the server receives DTLS traffic from a client, it SHOULD notify the administrator that DTLS is available for that client. It MAY mark the client as "DTLS Required". Allowing RADIUS/UDP and RADIUS/DTLS from the same client exposes the traffic to downbidding attacks and is NOT RECOMMENDED.

Client behavior When a RADIUS/DTLS client sends packet to the assigned RADIUS/DTLS port, all packets MUST be DTLS. RADIUS/UDP packets MUST NOT be sent to this port. RADIUS/DTLS clients SHOULD NOT probe servers to see if they support DTLS transport. Instead, clients SHOULD use DTLS as a transport layer only when administratively configured. If a client is configured to use DTLS and the server appears to be unresponsive, the client MUST NOT fall back to using RADIUS/UDP. Instead, the client should treat the server as being down. RADIUS clients often had multiple independent RADIUS implementations and/or processes that originate packets. This practice was simple to implement, but the result is that each independent subsystem must independently discover network issues or server failures. It is therefore RECOMMENDED that clients with multiple internal RADIUS sources use a local proxy. Clients may implement "pools" of servers for fail-over or load-balancing. These pools SHOULD NOT mix RADIUS/UDP and RADIUS/DTLS servers.This paragraph should probably be moved, as it also applies to RADIUS/TLS. Mixing secure transports with insecure ones is bad practice, regardless of UDP or TCP.

Session Management Where RADIUS/TLS can rely on the TCP state machine to perform session tracking, RADIUS/DTLS cannot. As a result, implementations of RADIUS/DTLS may need to perform session management of the DTLS session in the application layer. This subsection describes logically how this tracking is done. Implementations may choose to use the method described here, or another, equivalent method. We note that , already mandates a duplicate detection cache. The session tracking described below can be seen as an extension of that cache, where entries contain DTLS sessions instead of RADIUS/UDP packets. , describes how duplicate RADIUS/UDP requests result in the retransmission of a previously cached RADIUS/UDP response. Due to DTLS sequence window requirements, a server MUST NOT retransmit a previously sent DTLS packet. Instead, it should cache the RADIUS response packet, and re-process it through DTLS to create a new RADIUS/DTLS packet, every time it is necessary to retransmit a RADIUS response. There are some specs (e.g. watchdog, stateless session resumption, closing session if malformed packet or security checks fail) which are valid for both server and client. It might be worth to just move them here instead of having them in both the client and the server spec.

Server Session Management A RADIUS/DTLS server MUST track ongoing DTLS sessions for each client, based on the following 4-tuple:

• source IP address
• source port
• destination IP address
• destination port

Note that this 4-tuple is independent of IP address version (IPv4 or IPv6). Each 4-tuple points to a unique session entry, which usually contains the following information:

DTLS Session:

Any information required to maintain and manage the DTLS session.

Last Traffic:

A variable containing a timestamp that indicates when this session last received valid traffic. If "Last Traffic" is not used, this variable may not exist.

DTLS Data:

An implementation-specific variable that may contain information about the active DTLS session. This variable may be empty or nonexistent.

This data will typically contain information such as idle timeouts, session lifetimes, and other implementation-specific data.

Session Opening and Closing Session tracking is subject to Denial-of-Service (DoS) attacks due to the ability of an attacker to forge UDP traffic. RADIUS/DTLS servers SHOULD use the stateless cookie tracking technique described in . DTLS sessions SHOULD NOT be tracked until a ClientHello packet has been received with an appropriate Cookie value. Server implementation SHOULD have a way of tracking DTLS sessions that are partially set up. Servers MUST limit both the number and impact on resources of partial sessions. Sessions (both 4-tuple and entry) MUST be deleted when a TLS Closure Alert () or a fatal TLS Error Alert () is received.TODO: Suggestion from Alan: "if closed for any reason", but not sure if this is what we mean. When a session is deleted due to it failing security requirements, the DTLS session MUST be closed, any TLS session resumption parameters for that session MUST be discarded, and all tracking information MUST be deleted. Sessions MUST also be deleted when a non-RADIUS packet is received over the DTLS connection, a RADIUS packet fails validation due to a packet being malformed, or when it has an invalid Message-Authenticator or invalid Request Authenticator. There are other cases when the specifications require that a packet received via a DTLS session be "silently discarded". In those cases, implementations MAY delete the underlying session as described above. A session SHOULD NOT be deleted when a well-formed, but "unexpected", RADIUS packet is received over it. These requirements ensure the security while maintaining flexibility. Any security-related issue causes the connection to be closed. After security restrictions have been applied, any unexpected traffic may be safely ignored, as it cannot cause a security issue. This allows for future extensions to the RADIUS/DTLS specifications. As UDP does not guarantee delivery of messages, RADIUS/DTLS servers MUST maintain a "Last Traffic" timestamp per DTLS session. The granularity of this timestamp is not critical and could be limited to one-second intervals. The timestamp SHOULD be updated on reception of a valid RADIUS/DTLS packet, or a DTLS Heartbeat, but no more than once per interval. The timestamp MUST NOT be updated in other situations, such as when packets are "silently discarded". RADIUS/DTLS servers SHOULD implement session resumption, preferably stateless session resumption as given in . This practice lowers the time and effort required to start a DTLS session with a client and increases network responsiveness. Since UDP is stateless, the potential exists for the client to initiate a new DTLS session using a particular 4-tuple, before the server has closed the old session. For security reasons, the server MUST keep the old session active until either it has received secure notification from the client that the session is closed or the server decides to close the session based on idle timeouts. Taking any other action would permit unauthenticated clients to perform a DoS attack, by reusing a 4-tuple and thus causing the server to close an active (and authenticated) DTLS session. As a result, servers MUST ignore any attempts to reuse an existing 4-tuple from an active session. This requirement can likely be reached by simply processing the packet through the existing session, as with any other packet received via that 4-tuple. Non-compliant, or unexpected packets will be ignored by the DTLS layer.In RFC7360 there is a final paragraph about mitigation of the 4-tuple problem by using a local proxy. I'm not sure if this is the right place here, i'd rather move that to a general "Implementation Guidelines" paragraph.

Client Session Management RADIUS/DTLS clients SHOULD use PMTU discovery to determine the PMTU between the client and server, prior to sending any RADIUS traffic. DTLS sessions MUST be deleted when a RADIUS packet fails validation due to a packet being malformed, or when it has an invalid Message-Authenticator or invalid Response Authenticator.Maybe modify this text to be more similar to the TLS specific text here. There are other cases, when the specifications require that a packet received via a DTLS session be "silently discarded". In those cases, implementations MAY delete the underlying DTLS session. RADIUS/DTLS clients SHOULD NOT send both RADIUS/UDP and RADIUS/DTLS packets to different servers from the same source socket. This practice causes increased complexity in the client application and increases the potential for security breaches due to implementation issues. RADIUS/DTLS clients SHOULD implement session resumption, preferably stateless session resumption as given in . This practice lowers the time and effort required to start a DTLS session with a server and increases network responsiveness.

Security Considerations As this specification relies on the existing TLS and DTLS specifications, all security considerations for these protocols also apply to the (D)TLS portions of RADIUS/(D)TLS. For RADIUS however, many security considerations raised in the RADIUS documents are related to RADIUS encryption and authorization. Those issues are largely mitigated when (D)TLS is used as a transport method, since encryption and authorization is achieved on the (D)TLS layer. The issues that are not mitigated by this specification are related to the RADIUS packet format and handling, which is unchanged in this specification. A few remaining security considerations and notes to administrators deploying RADIUS/(D)TLS are listed below.

RADIUS Proxies RADIUS/(D)TLS provides authentication, integrity and confidentiality protection for RADIUS traffic between two RADIUS peers. In the presence of proxies, these intermediate proxies can still inspect the individual RADIUS packets, i.e., "end-to-end" encryption on the RADIUS layer is not provided. Where intermediate proxies are untrusted, it is desirable to use other RADIUS mechanisms to prevent RADIUS packet payload from inspection by such proxies. One common method to protect passwords is the use of the Extensible Authentication Protocol (EAP) and EAP methods that utilize TLS. Additionally, when RADIUS proxies are used, the RADIUS client has no way of ensuring that the complete path of the RADIUS packet is protected, since RADIUS routing is done hop-by-hop and any intermediate proxy may be configured, after receiving a RADIUS packet via RADIUS/(D)TLS from one peer, to forward this packet to a different peer using the RADIUS/UDP transport profile. There is no technical solution to this problem with the current specification. Where the confidentiality of the contents of the RADIUS packet across the whole path is required, organizational solutions need to be in place, that ensure that every intermediate RADIUS proxy is configured to forward the RADIUS packets using RADIUS/(D)TLS as transport. TODO: Mabe add a reference to handling dynamic discovery (RFC7585) here too, and (as per Alans comments) that this issue is best resolved by limiting use of proxies.

Usage of null encryption cipher suites for debugging For debugging purposes, some TLS implementation offer cipher suites with NULL encryption, to allow inspection of the plaintext with packet sniffing tools. Since with RADIUS/(D)TLS the RADIUS shared secret is set to a static string ("radsec" for RADIUS/TLS, "radius/dtls" for RADIUS/DTLS), using a NULL encryption cipher suite will also result in complete disclosure of the whole RADIUS packet, including the encrypted RADIUS attributes, to any party eavesdropping on the conversation. To prevent this, while keeping a NULL encryption cipher suite active, the only option is to set a different shared secret for RADIUS. In this case, the security considerations for confidentiality of RADIUS/UDP packets apply. Following the recommendations in , this specification forbids the usage of NULL encryption cipher suites for RADIUS/(D)TLS.

Possibility of Denial-of-Service attacks Both RADIUS/TLS and RADIUS/DTLS have a considerable higher amount of data that the server needs to store in comparison to RADIUS/UDP. Therefore, an attacker could try to exhaust server resources. With RADIUS/UDP, any bogus RADIUS packet would fail the cryptographic checks and the server would silently discard the bogus packet. For RADIUS/(D)TLS, the server needs to perform at least a partial TLS handshake to determine whether or not the client is authorized. Performing a (D)TLS handshake is more complex than the cryptographic check of a RADIUS packet. An attacker could try to trigger a high number of (D)TLS handshakes at the same time, resulting in a high server load and potentially a Denial-of-Service. To prevent this attack, a RADIUS/(D)TLS server SHOULD have configurable limits on new connection attempts. Both TLS and DTLS need to store session information for each open (D)TLS session. Especially with DTLS, a bogus or misbehaving client could open an excessive number of DTLS sessions. This session tracking could lead to a resource exhaustion on the server side, triggering a Denial-of-Service. Therefore, RADIUS/(D)TLS servers MUST limit the absolute number of sessions they can track and SHOULD expose this limit as configurable option to the administrator. When the total number of sessions tracked is going to exceed the configured limit, servers MAY free up resources by closing the session that has been idle for the longest time. Doing so may free up idle resources that then allow the server to accept a new session. RADIUS/DTLS servers MUST limit the number of partially open DTLS sessions and SHOULD expose this limit as configurable option to the administrator. To prevent resource exhaustion by partially opening a large number of DTLS sessions, RADIUS/DTLS servers SHOULD have a timeout on partially open DTLS sessions. We recommend a limit of a few seconds, implementations SHOULD expose this timeout as configurable option to the administrator. If a DTLS session is not established within this timeframe, it is likely that this is a bogus connection. In contrast, an established session might not send packets for longer periods of time, but since the peers are mutually authenticated this does not pose a problem other than the problems mentioned before. A different means of prevention is IP filtering. If the IP range that the server expects clients to connect from is restricted, then the server can simply reject or drop all connection attempts from outside those ranges. If every RADIUS/(D)TLS client is configured with an IP range, then the server does not even have to perform a partial TLS handshake if the connection attempt comes from outside every allowed range, but can instead immediately drop the connection. To perform this lookup efficiently, RADIUS/(D)TLS servers SHOULD keep a list of the cumulated permitted IP ranges, individually for each transport.

Session Closing If malformed RADIUS packets are received or the packets fail the authenticator checks, this specification requires that the (D)TLS session be closed. The reason is that the session is expected to be used for transport of RADIUS packets only. Any non-RADIUS traffic on that session means the other party is misbehaving and is potentially a security risk. Similarly, any RADIUS traffic failing authentication vector or Message-Authenticator validation means that two parties do not have a common shared secret. Since the shared secret is static, this again means the other party is misbehaving. We wish to avoid the situation where a third party can send well-formed RADIUS packets to a RADIUS proxy that cause a (D)TLS session to close. Therefore, in other situations, the session SHOULD remain open in the face of non-conforming packets. Any malformed RADIUS packets sent by a third party will go through the security checks of the RADIUS proxy upon reception and will not be forwarded. Well-formed RADIUS packets with portions that the proxy does not understand do not pose a security risk to the security properties of the RADIUS/(D)TLS session and can be forwarded. This ensures forward compatibility with future RADIUS extensions.

Migrating from RADIUS/UDP to RADIUS/(D)TLS Since RADIUS/UDP security relies on the MD5 algorithm, which is considered insecure, using RADIUS/UDP over insecure networks is risky. We therefore recommend to migrate from RADIUS/UDP to RADIUS/(D)TLS. Within this migration process, however, there are a few items that need to be considered by administrators. Firstly, administrators may be tempted to simply migrate from RADIUS/UDP to RADIUS/(D)TLS with (D)TLS-PSK and reuse the RADIUS shared secret as (D)TLS-PSK. While this may seem like an easy way to upgrade RADIUS/UDP to RADIUS/(D)TLS, the cryptographic problems with the RADIUS/UDP shared secret render the shared secret potentially compromised. Using a potentially compromised shared secret as TLS-PSK compromises the whole TLS connection. Therefore, any shared secret used with RADIUS/UDP before MUST NOT be used with RADIUS/(D)TLS and (D)TLS-PSK. Implementers MUST NOT reuse the configuration option for the RADIUS/UDP shared secret for the (D)TLS-PSK to prevent accidental reuse. When upgrading from RADIUS/UDP to RADIUS/(D)TLS, there may be a period of time, where the connection between client and server is configured for both transport profiles. If the old RADIUS/UDP configuration is left configured, but not used in normal operation, e.g. due to a fail-over configuration that prefers RADIUS/(D)TLS, an attacker could disrupt the RADIUS/(D)TLS communication and force a downgrade to RADIUS/UDP. To prevent this it is RECOMMENDED that, when the migration to RADIUS/(D)TLS is completed, the RADIUS/UDP configuration is removed. RADIUS/(D)TLS clients MUST NOT fall back to RADIUS/UDP if the RADIUS/(D)TLS communication fails, unless explicitly configured this way.

Client Subsystems Many traditional clients treat RADIUS as subsystem-specific. That is, each subsystem on the client has its own RADIUS implementation and configuration. These independent implementations work for simple systems, but break down for RADIUS when multiple servers, fail-over and load-balancing are required. With (D)TLS enabled, these problems are expected to get worse. We therefore recommend in these situations to use a local proxy that arbitrates all RADIUS traffic between the client and all servers. This proxy will encapsulate all knowledge about servers, including security policies, fail-over and load-balancing. All client subsystems should communicate with this local proxy, ideally over a loopback address. The benefit of this configuration is that there is one place in the client that arbitrates all RADIUS traffic. Subsystems that do not implement RADIUS/(D)TLS can remain unaware of (D)TLS. (D)TLS sessions opened by the proxy can remain open for a long period of time, even when client subsystems are restarted. The proxy can do RADIUS/UDP to some servers and RADIUS/(D)TLS to others. Delegation of responsibilities and separation of tasks are important security principles. By moving all RADIUS/(D)TLS knowledge to a (D)TLS-aware proxy, security analysis becomes simpler, and enforcement of correct security becomes easier.

Loopback-Attack on Peers acting as Server and Client TODO Rough problem description to visualize the problem for others. Will be removed and replaced with text explaining the issue and possible mitigations: Preconditions: Peer A is configured with a client certificate for sending packets via dynamic discovery. The certificate has a specific OID indicating it as a "roaming consortium client" certificate. The configuration expects a server certificate from the server with an OID for a "roaming consortium server" certificate and does not perform more checks apart from the trust chain checks. Peer A is also configured with a server certificate for receiving packets via dynamic discovery. The server certificate has a specific OID indicating it as a "roaming consortium server" certificate. The configuration expects a client certificate from the client with an OID for a "roaming consortium client" certificate and does not perform more checks apart from the trust chain checks. For the sake of this example we can say that both certificates come from the same CA and that this CA is marked as trusted. Attack: Peer A (as Client A) tries to open RADIUS/TLS connection to Server B. The attacker intercepts the connection and mirrors it back to A (now acting as Server A) Server A sends the server certificate with the server OID. Client A receives it, accepts it, since it sees the server OID and sends the client certificate. Server A receives it and also accepts it, since it sees the client OID. Now Peer A has a loop. Client A sends packets, believing they are sent to the right home server. Server A receives packets from a valid-looking client and forwards them, since it is not responsible for the realm. Now every packet is stuck in an endless-loop and the attacker just has to bounce the traffic back-and-forth, possibly leading to a complete denial-of-service. Ideas for solutions:

• Don't accept your own certificate.
  • May not be what you want.
• Remember the client random and compare the server random
  • May still not be good enough. Depending on the implementation could lead to different race conditions being triggered.
  • Maybe not all TLS implementations allow you to get the client random?
• Send a randomized number in the TLS client hello
  • Number could be generated at startup (or even changed once in a while). Every outgoing TLS has this in the client hello, the server can check if the "ID" number of the other end is the same to its own. If it is: Drop the connection.
  • But needs a TLS extension (or some other smart way of doing this with the tools available)

Design Decisions Many of the design decisions of RADIUS/TLS and RADIUS/DTLS can be found in and . This section will discuss the rationale behind significant changes from the experimental specification.

Mandatory-to-implement transports With the merging of RADIUS/TLS and RADIUS/DTLS the question of mandatory-to-implement transports arose. In order to avoid incompatibilities, there were two possibilities: Either mandate one of the transports for all implementations or mandate the implementation of both transports for either the server or the client. As of the time writing, RADIUS/TLS is widely adapted for some use cases (see ). However, TLS has some serious drawbacks when used for RADIUS transport. Especially the sequential nature of the connection and the connected issues like Head-of-Line blocking could create problems. Therefore, the decision was made that RADIUS servers must implement both transports. For RADIUS clients, that may run on more constrained nodes, the implementations can choose to implement only the transport, that is better suited for their needs.

Mandatory-to-implement trust profiles mandates the implementation of the trust profile "certificate with PKIX trust model" for both clients and servers. The experience of the deployment of RADIUS/TLS as specified in has shown that most actors still rely on RADIUS/UDP. Since dealing with certificates can create a lot of issues, both for implementers and administrators, for the re-specification we wanted to create an alternative to insecure RADIUS transports like RADIUS/UDP that can be deployed easily without much additional administrative overhead. As with the supported transports, the assumption is that RADIUS servers are generally believed to be less constrained than RADIUS clients. Since some client implementations already support using certificates for mutual authentication and there are several use cases, where pre-shared keys are not usable (e.g. a dynamic federation with changing members), the decision was made that, analog to the supported transports, RADIUS servers must implement both certificates with PKIX trust model and TLS-PSK as means of mutual authentication. RADIUS clients again can choose which method is better suited for them, but must, for compatibility reasons, implement at least one of the two.

Changes in application of TLS The original specification of RADIUS/TLS does not forbid the usage of compression in the TLS layer. As per , compression should not be used due to the possibility of compression-related attacks, unless the application protocol is proven to be not open to such attacks. Since some attributes of the RADIUS packets within the TLS tunnel contain values that an attacker could at least partially choose (i.e. username, MAC address or EAP message), there is a possibility for compression-related attacks, that could potentially reveal data in other RADIUS attributes through length of the TLS record. To circumvent this attack, this specification forbids the usage of TLS compression.

IANA Considerations Upon approval, IANA should update the Reference to radsec in the Service Name and Transport Protocol Port Number Registry:

• Service Name: radsec
• Port Number: 2083
• Transport Protocol: tcp/udp
• Description: Secure RADIUS Service
• Assignment notes: The TCP port 2083 was already previously assigned by IANA for "RadSec", an early implementation of RADIUS/TLS, prior to issuance of the experimental RFC 6614. [RFCXXXX] updates RFC 6614 (RADIUS/TLS) and RFC 7360 (RADIUS/DTLS), while maintaining backward compatibility, if configured. For further details see RFC 6614, Appendix A or [RFCXXXX] .

References Normative References This document describes a protocol for carrying authentication, authorization, and configuration information between a Network Access Server which desires to authenticate its links and a shared Authentication Server. [STANDARDS-TRACK] This document describes a protocol for carrying accounting information between a Network Access Server and a shared Accounting Server. This memo provides information for the Internet community. This document describes a currently deployed extension to the Remote Authentication Dial In User Service (RADIUS) protocol, allowing dynamic changes to a user session, as implemented by network access server products. This includes support for disconnecting users and changing authorizations applicable to a user session. This memo provides information for the Internet community. Many application technologies enable secure communication between two entities by means of Transport Layer Security (TLS) with Internet Public Key Infrastructure using X.509 (PKIX) certificates. This document specifies procedures for representing and verifying the identity of application services in such interactions. This document obsoletes RFC 6125. In many standards track documents several words are used to signify the requirements in the specification. These words are often capitalized. This document defines these words as they should be interpreted in IETF documents. This document specifies an Internet Best Current Practices for the Internet Community, and requests discussion and suggestions for improvements. RFC 2119 specifies common key words that may be used in protocol specifications. This document aims to reduce the ambiguity by clarifying that only UPPERCASE usage of the key words have the defined special meanings. This document defines Remote Authentication Dial In User Service (RADIUS) support for the Extensible Authentication Protocol (EAP), an authentication framework which supports multiple authentication mechanisms. In the proposed scheme, the Network Access Server (NAS) forwards EAP packets to and from the RADIUS server, encapsulated within EAP-Message attributes. This has the advantage of allowing the NAS to support any EAP authentication method, without the need for method- specific code, which resides on the RADIUS server. While EAP was originally developed for use with PPP, it is now also in use with IEEE 802. This memo provides information for the Internet community. This document discusses transport issues that arise within protocols for Authentication, Authorization and Accounting (AAA). It also provides recommendations on the use of transport by AAA protocols. This includes usage of standards-track RFCs as well as experimental proposals. [STANDARDS-TRACK] This document describes a deployed extension to the Remote Authentication Dial In User Service (RADIUS) protocol, enabling clients to query the status of a RADIUS server. This extension utilizes the Status-Server (12) Code, which was reserved for experimental use in RFC 2865. This document is not an Internet Standards Track specification; it is published for informational purposes. This document specifies the Transmission Control Protocol (TCP). TCP is an important transport-layer protocol in the Internet protocol stack, and it has continuously evolved over decades of use and growth of the Internet. Over this time, a number of changes have been made to TCP as it was specified in RFC 793, though these have only been documented in a piecemeal fashion. This document collects and brings those changes together with the protocol specification from RFC 793. This document obsoletes RFC 793, as well as RFCs 879, 2873, 6093, 6429, 6528, and 6691 that updated parts of RFC 793. It updates RFCs 1011 and 1122, and it should be considered as a replacement for the portions of those documents dealing with TCP requirements. It also updates RFC 5961 by adding a small clarification in reset handling while in the SYN-RECEIVED state. The TCP header control bits from RFC 793 have also been updated based on RFC 3168. Transport Layer Security (TLS) and Datagram Transport Layer Security (DTLS) are used to protect data exchanged over a wide range of application protocols and can also form the basis for secure transport protocols. Over the years, the industry has witnessed several serious attacks on TLS and DTLS, including attacks on the most commonly used cipher suites and their modes of operation. This document provides the latest recommendations for ensuring the security of deployed services that use TLS and DTLS. These recommendations are applicable to the majority of use cases. RFC 7525, an earlier version of the TLS recommendations, was published when the industry was transitioning to TLS 1.2. Years later, this transition is largely complete, and TLS 1.3 is widely available. This document updates the guidance given the new environment and obsoletes RFC 7525. In addition, this document updates RFCs 5288 and 6066 in view of recent attacks. The specification for enhanced mail system status codes, RFC 3463, establishes a new code model and lists a collection of status codes. While it anticipated that more codes would be added over time, it did not provide an explicit mechanism for registering and tracking those codes. This document specifies an IANA registry for mail system enhanced status codes, and initializes that registry with the codes so far established in published standards-track documents, as well as other codes that have become established in the industry. This document specifies an Internet Best Current Practices for the Internet Community, and requests discussion and suggestions for improvements. This document specifies version 1.2 of the Datagram Transport Layer Security (DTLS) protocol. The DTLS protocol provides communications privacy for datagram protocols. The protocol allows client/server applications to communicate in a way that is designed to prevent eavesdropping, tampering, or message forgery. The DTLS protocol is based on the Transport Layer Security (TLS) protocol and provides equivalent security guarantees. Datagram semantics of the underlying transport are preserved by the DTLS protocol. This document updates DTLS 1.0 to work with TLS version 1.2. [STANDARDS-TRACK] This document specifies version 1.3 of the Transport Layer Security (TLS) protocol. TLS allows client/server applications to communicate over the Internet in a way that is designed to prevent eavesdropping, tampering, and message forgery. This document updates RFCs 5705 and 6066, and obsoletes RFCs 5077, 5246, and 6961. This document also specifies new requirements for TLS 1.2 implementations. This document specifies version 1.3 of the Datagram Transport Layer Security (DTLS) protocol. DTLS 1.3 allows client/server applications to communicate over the Internet in a way that is designed to prevent eavesdropping, tampering, and message forgery. The DTLS 1.3 protocol is based on the Transport Layer Security (TLS) 1.3 protocol and provides equivalent security guarantees with the exception of order protection / non-replayability. Datagram semantics of the underlying transport are preserved by the DTLS protocol. This document obsoletes RFC 6347. This memo profiles the X.509 v3 certificate and X.509 v2 certificate revocation list (CRL) for use in the Internet. An overview of this approach and model is provided as an introduction. The X.509 v3 certificate format is described in detail, with additional information regarding the format and semantics of Internet name forms. Standard certificate extensions are described and two Internet-specific extensions are defined. A set of required certificate extensions is specified. The X.509 v2 CRL format is described in detail along with standard and Internet-specific extensions. An algorithm for X.509 certification path validation is described. An ASN.1 module and examples are provided in the appendices. [STANDARDS-TRACK] This document specifies Version 1.2 of the Transport Layer Security (TLS) protocol. The TLS protocol provides communications security over the Internet. The protocol allows client/server applications to communicate in a way that is designed to prevent eavesdropping, tampering, or message forgery. [STANDARDS-TRACK] This document provides specifications for existing TLS extensions. It is a companion document for RFC 5246, "The Transport Layer Security (TLS) Protocol Version 1.2". The extensions specified are server_name, max_fragment_length, client_certificate_url, trusted_ca_keys, truncated_hmac, and status_request. [STANDARDS-TRACK] This document specifies a means to find authoritative RADIUS servers for a given realm. It is used in conjunction with either RADIUS over Transport Layer Security (RADIUS/TLS) or RADIUS over Datagram Transport Layer Security (RADIUS/DTLS). The Domain Name System Security Extensions (DNSSEC) add data origin authentication and data integrity to the Domain Name System. This document introduces these extensions and describes their capabilities and limitations. This document also discusses the services that the DNS security extensions do and do not provide. Last, this document describes the interrelationships between the documents that collectively describe DNSSEC. [STANDARDS-TRACK] This document specifies a new certificate type and two TLS extensions for exchanging raw public keys in Transport Layer Security (TLS) and Datagram Transport Layer Security (DTLS). The new certificate type allows raw public keys to be used for authentication. The Extensible Authentication Protocol (EAP), defined in RFC 3748, enables extensible network access authentication. This document specifies the EAP key hierarchy and provides a framework for the transport and usage of keying material and parameters generated by EAP authentication algorithms, known as "methods". It also provides a detailed system-level security analysis, describing the conditions under which the key management guidelines described in RFC 4962 can be satisfied. [STANDARDS-TRACK] This document describes common issues seen in Remote Authentication Dial In User Service (RADIUS) implementations and suggests some fixes. Where applicable, ambiguities and errors in previous RADIUS specifications are clarified. [STANDARDS-TRACK] This document describes a mechanism that enables the Transport Layer Security (TLS) server to resume sessions and avoid keeping per-client session state. The TLS server encapsulates the session state into a ticket and forwards it to the client. The client can subsequently resume a session using the obtained ticket. This document obsoletes RFC 4507. [STANDARDS-TRACK] This document describes the Heartbeat Extension for the Transport Layer Security (TLS) and Datagram Transport Layer Security (DTLS) protocols. The Heartbeat Extension provides a new protocol for TLS/DTLS allowing the usage of keep-alive functionality without performing a renegotiation and a basis for path MTU (PMTU) discovery for DTLS. [STANDARDS-TRACK] Informative References FreeRADIUS This document defines Application-Layer Protocol Negotiation Extensions for use with RADIUS/TLS and RADIUS/DTLS. These extensions permit the negotiation of an application protocol variant of RADIUS, called "RADIUS/1.1". No changes are made to RADIUS/UDP or RADIUS/ TCP. The extensions allow the negotiation of a transport profile where the RADIUS shared secret is no longer used, and all MD5-based packet authentication and attribute obfuscation methods are removed. This document updates RFC2865, RFC2866, RFC5176, RFC6613, RFC6614, and RFC 7360. This document describes the architecture of the eduroam service for federated (wireless) network access in academia. The combination of IEEE 802.1X, the Extensible Authentication Protocol (EAP), and RADIUS that is used in eduroam provides a secure, scalable, and deployable service for roaming network access. The successful deployment of eduroam over the last decade in the educational sector may serve as an example for other sectors, hence this document. In particular, the initial architectural choices and selection of standards are described, along with the changes that were prompted by operational experience. This document specifies a transport profile for RADIUS using Transport Layer Security (TLS) over TCP as the transport protocol. This enables dynamic trust relationships between RADIUS servers. [STANDARDS-TRACK] The Remote Authentication Dial-In User Server (RADIUS) protocol has, until now, required the User Datagram Protocol (UDP) as the underlying transport layer. This document defines RADIUS over the Transmission Control Protocol (RADIUS/TCP), in order to address handling issues related to RADIUS over Transport Layer Security (RADIUS/TLS). It permits TCP to be used as a transport protocol for RADIUS only when a transport layer such as TLS or IPsec provides confidentiality and security. This document defines an Experimental Protocol for the Internet community. The RADIUS protocol defined in RFC 2865 has limited support for authentication and encryption of RADIUS packets. The protocol transports data in the clear, although some parts of the packets can have obfuscated content. Packets may be replayed verbatim by an attacker, and client-server authentication is based on fixed shared secrets. This document specifies how the Datagram Transport Layer Security (DTLS) protocol may be used as a fix for these problems. It also describes how implementations of this proposal can coexist with current RADIUS systems. FreeRADIUS This document provides implementation and operational considerations for using TLS-PSK with RADIUS/TLS (RFC6614) and RADIUS/DTLS (RFC7360). The purpose of the document is to help smooth the operational transition from the use of the RADIUS/UDP to RADIUS/TLS.

Lessons learned from deployments of the Experimental There are at least two major (world-scale) deployments of . This section will discuss lessens learned from these deployments, that influenced this document.

eduroam eduroam is a globally operating Wi-Fi roaming consortium exclusively for persons in Research and Education. For an extensive background on eduroam and its authentication fabric architecture, refer to . Over time, more than a dozen out of 100+ national branches of eduroam used RADIUS/TLS in production to secure their country-to-country RADIUS proxy connections. This number is big enough to attest that the protocol does work, and scales. The number is also low enough to wonder why RADIUS/UDP continued to be used by a majority of country deployments despite its significant security issues. Operational experience reveals that the main reason is related to the choice of PKIX certificates for securing the proxy interconnections. Compared to shared secrets, certificates are more complex to handle in multiple dimensions:

• Lifetime: PKIX certificates have an expiry date, and need administrator attention and expertise for their renewal
• Validation: The validation of a certificate (both client and server) requires contacting a third party to verify the revocation status. This either takes time during session setup (OCSP checks) or requires the presence of a fresh CRL on the server - this in turn requires regular update of that CRL.
• Issuance: PKIX certificates carry properties in the Subject and extensions that need to be vetted. Depending on the CA policy, a certificate request may need significant human intervention to be verified. In particular, the authorisation of a requester to operate a server for a particular NAI realm needs to be verified. This rules out public "browser-trusted" CAs; eduroam is operating a special-purpose CA for eduroam RADIUS/TLS purposes.
• Automatic failure over time: CRL refresh and certificate renewal must be attended to regularly. Failure to do so leads to failure of the authentication service. Among other reasons, employee churn with incorrectly transferred or forgotten responsibilities is a risk factor.

It appears that these complexities often outweigh the argument of improved security; and a fallback to RADIUS/UDP is seen as the more appealing option. It can be considered an important result of the experiment in that providing less complex ways of operating RADIUS/TLS are required. The more thoroughly specified provisions in the current document towards TLS-PSK and raw public keys are a response to this insight. On the other hand, using RADIUS/TLS in combination with Dynamic Discovery as per necessitates the use of PKIX certificates. So, the continued ability to operate with PKIX certificates is also important and cannot be discontinued without sacrificing vital functionality of large roaming consortia.

Wireless Broadband Alliance's OpenRoaming OpenRoaming is a globally operating Wi-Fi roaming consortium for the general public, operated by the Wireless Broadband Alliance (WBA). With its (optional) settled usage of hotspots, the consortium requires both RADIUS authentication as well as RADIUS accounting. The consortium operational procedures were defined in the late 2010s when and were long available. The consortium decided to fully base itself on these two RFCs. In this architecture, using PSKs or raw public keys is not an option. The complexities around PKIX certificates as discussed in the previous section are believed to be controllable: the consortium operates its own special-purpose CA and can rely on a reliable source of truth for operator authorisation (becoming an operator requires a paid membership in WBA); expiry and revocation topics can be expected to be dealt with as high-priority because of the monetary implications in case of infrastructure failure during settled operation.

Participating in more than one roaming consortium It is possible for a RADIUS/TLS (home) server to participate in more than one roaming consortium, i.e. to authenticate its users to multiple clients from distinct consortia, which present client certificates from their respective consortium's CA; and which expect the server to present a certificate from the matching CA. The eduroam consortium has chosen to cooperate with (the settlement-free parts of) OpenRoaming to allow eduroam users to log in to (settlement-free) OpenRoaming hotspots. eduroam RADIUS/TLS servers thus may be contacted by OpenRoaming clients expecting an OpenRoaming server certificate, and by eduroam clients expecting an eduroam server certificate. It is therefore necessary to decide on the certificate to present during TLS session establishment. To make that decision, the availability of Trusted CA Indication in the client TLS message is important. It can be considered an important result of the experiment in that Trusted CA Indication is an important asset for inter-connectivity of multiple roaming consortia.

Interoperable Implementations

Backward compatibility TODO describe necessary steps to configure common servers for compatibility with this version. Hopefully the differences to are small enough that almost no config change is necessary.

Acknowledgments Thanks to the original authors of RFC 6613, RFC 6614 and RFC 7360: Alan DeKok, Stefan Winter, Mike McCauley, Stig Venaas and Klaas Vierenga. Thanks to Arran Curdbard-Bell for text around keepalives and the Status-Server watchdog algorithm. Thanks to Alan DeKok for his constant review of this document over its whole process and his many text contributions, like text around forwarding issues between TCP and UDP based transports.